No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Tecmolog - Adaptador en T de metal de 3/8 pulgadas para válvula angular de 3/8 pulgadas
Especificaciones del producto:
Material: Acero inoxidable
Acabado: Níquel cepillado
Método de instalación: Tornillo
Tamaño de conexión
Rosca macho G1/2" (20,54 mm)
Rosca macho de 13,72 mm de EE. UU
Rosca hembra de 3/8 pulgadas de EE. UU
Es una buena válvula en T para que conectes la línea de suministro de agua de 9/16 pulgadas y la manguera de rociador de bidé G1/2 pulgadas.
Detalles del producto:
La rosca hembra de 9/16 pulgadas se conecta a la válvula de tope de ángulo estándar de EE. UU
Las roscas macho se conectan a la línea de suministro de agua de 9/16 pulgadas y manguera flexible G1/2 pulgadas
1 conector en T 3/8 x 3/8 x 1/2
3 arandelas de goma
Tony & Kimmy
Comentado en los Estados Unidos el 18 de enero de 2025
The 3/8 compression on top doesn’t fit well with the 3/8 compression hose. Usually compression fit the tube overlapping each other with the rubber pressing down when tightening to create a seal. The mating surface of this isn’t great . Even with teflon tape it leaks. I added an extra gasket to help join the two surfaces better however not sure about long term reliability .
mehran
Comentado en Canadá el 17 de septiembre de 2024
it made by good materials. it was not suitable for my hose. because the 3/8 connection has a small hole and my current hose did not fit, but I kept it to find a new hose later
Rumi Mohammad
Comentado en Canadá el 8 de abril de 2024
Female and 1/2 ends fit easily without leaks. Spent an hour trying to get the male end to fit. Tried with and without the gasket. Tried with and without the included tape/thread. It just would not fit and leaked every time.The exisiting supply line female fits the existing male snugly without leaks. Therefore, I can only conclue the thread on this male is just too wide.Solved the problem of skirted toilets by getting 7/8 x 7/8 extenders with ridged female nuts. Worked on the first try, by hand, with no leaks.
Yoram Adler
Comentado en los Estados Unidos el 20 de septiembre de 2023
All the bidet additions to the toilet, whether under the seat or outside, assume you are dealing with the same plumbing conditions. on my toilet, it's extremely difficult if not impossible to reach under the tank and replace the t-shape 3-way diverter/adopter. This one is a perfect solution and it took me some time to find it on Amazon. it fits at the entry point of the water, out of the wall where you usually see the shut-off valve for the water going to the toilet. I had no use for the adopter that came with my bidet kit. I am glad someone thought that not every toilet is built the same. Mine Is "Mr. Thomas By Icera". I hope this will help the next buyer with the same situation.
Jai Prakash Singh
The concept of this adopter is good that 3/8” line could be diverted to 1/2” without a coupler but unfortunately this item is fabricated smaller than the standard 3/8” fitting sizes from ACE hardware and also from the building fittings in Dubai.
Productos recomendados
Mex $368.95
Mex $ 180 .00 Mex $180.00
Mex $419.07
Mex $ 226 .00 Mex $226.00
Mex $191.32
Mex $ 97 .00 Mex $97.00