No hay artículos en el carro
No hay artículos en el carro Cabezal de extrusión de extremo caliente mejorado TZ 2.0 (estructura de boquilla roscada totalmente metálica, que no es fácil de doblar y romper), y el caudal de consumo de impresión puede ser tan alto como 35 mm³/s
➤Característica:
●Radiador de aluminio: pequeño y ligero, fabricado de aluminio con bloque de calefacción integrado para garganta y boquillas de acero endurecido roscadas reemplazables.
● Fijo por tornillos de aleación de tazón: el bloque de calefacción está conectado al radiador a través de dos tornillos de aleación dorada para evitar que se doblen y rompan la garganta durante la impresión de alta velocidad.
● El material de la garganta del bloque calefactor se actualiza: el bloque calefactor se actualiza a cobre chapado en cromo y niquelado para una conducción rápida del calor y resistencia a la impresión a alta temperatura. El tubo de aleación está rodeado de cobre chapado en cromo para una mejor disipación del calor
● Mejora de la boquilla del bloque de calefacción: el bloque de calefacción se actualiza a chapado en cromo-cobre y níquel, que puede soportar una impresión a alta temperatura de 550 ℃ y tiene una conductividad térmica rápida; la boquilla está hecha de acero endurecido SKD11, que se ha templado y endurecido y se puede calentar hasta 550 ℃ o superior, por lo que es más resistente al desgaste y prolonga la vida útil
● Mejora de la estructura de la boquilla: el bloque de calentamiento y la boquilla están roscados, y la boquilla está en contacto con el escalón inferior de la garganta para resolver firmemente el problema de caídas y reducir la posibilidad de fugas de material. La boquilla desmontable reduce el costo de uso
● Rosca de tornillo superior: el radiador y la garganta se fijan por el tornillo superior, la conexión es estable, desmontable y reemplazable, reduciendo el costo de uso
➤Compatible:
● Compatible con Bambu Lab P1/P1S.
➤Paquete:
● 1 llave de extremo abierto de 4 mm.
● 1 boquilla de acero endurecido de 0,2/0,4/0,6 mm.
1 grasa térmica.
● 1 mango hexagonal de 1,5.
● 1 clip de fijación.
1 funda de silicona. 1 calentador de cerámica.
● 1 termistor.
Customer
Comentado en Canadá el 31 de marzo de 2025
This hotend works great, and includes two 0.4, a 0.6 and a 0.2. The thermistor and heater worked as good as the Bambu one, even included thermal paste.I ordered it because it was fast to get but the product is great so far too.
Customer
Comentado en Canadá el 31 de marzo de 2025
This hotend works great, and includes two 0.4, a 0.6 and a 0.2. The thermistor and heater worked as good as the Bambu one, even included thermal paste.I ordered it because it was fast to get but the product is great so far too.
Customer
Comentado en Canadá el 31 de marzo de 2025
This hotend works great, and includes two 0.4, a 0.6 and a 0.2. The thermistor and heater worked as good as the Bambu one, even included thermal paste.I ordered it because it was fast to get but the product is great so far too.
Customer
Comentado en Canadá el 31 de marzo de 2025
This hotend works great, and includes two 0.4, a 0.6 and a 0.2. The thermistor and heater worked as good as the Bambu one, even included thermal paste.I ordered it because it was fast to get but the product is great so far too.
Customer
Comentado en Canadá el 31 de marzo de 2025
This hotend works great, and includes two 0.4, a 0.6 and a 0.2. The thermistor and heater worked as good as the Bambu one, even included thermal paste.I ordered it because it was fast to get but the product is great so far too.
Customer
Comentado en Canadá el 31 de marzo de 2025
This hotend works great, and includes two 0.4, a 0.6 and a 0.2. The thermistor and heater worked as good as the Bambu one, even included thermal paste.I ordered it because it was fast to get but the product is great so far too.
Customer
Comentado en Canadá el 31 de marzo de 2025
This hotend works great, and includes two 0.4, a 0.6 and a 0.2. The thermistor and heater worked as good as the Bambu one, even included thermal paste.I ordered it because it was fast to get but the product is great so far too.
Customer
Comentado en Canadá el 31 de marzo de 2025
This hotend works great, and includes two 0.4, a 0.6 and a 0.2. The thermistor and heater worked as good as the Bambu one, even included thermal paste.I ordered it because it was fast to get but the product is great so far too.
UJM81
Comentado en los Estados Unidos el 23 de febrero de 2025
It took a couple of extra days to get these since I got a bottle of mascara instead of them. Once that was returned, they arrived the following day and were as described. They are a good selection for the cost, and will be helpful when I print with more abrasive filament.UPDATE- The Artillery X4 Plus uses a small diameter tip with small flat spots (maybe 4mm?) to remove it. The removal tool is only available through them, so it's a lengthy delay and high cost to get one. That should come with the printer. I found a 4-way lug wrench style of tool I had from another printer would work via the smallest opening, but I managed to break the thermistor when I tried to swap the nozzles. These nozzles are the same length and thread, so they should work OK, plus they use a common wrench to install or remove. Overall a poorly designed setup.
UJM81
Comentado en los Estados Unidos el 23 de febrero de 2025
It took a couple of extra days to get these since I got a bottle of mascara instead of them. Once that was returned, they arrived the following day and were as described. They are a good selection for the cost, and will be helpful when I print with more abrasive filament.UPDATE- The Artillery X4 Plus uses a small diameter tip with small flat spots (maybe 4mm?) to remove it. The removal tool is only available through them, so it's a lengthy delay and high cost to get one. That should come with the printer. I found a 4-way lug wrench style of tool I had from another printer would work via the smallest opening, but I managed to break the thermistor when I tried to swap the nozzles. These nozzles are the same length and thread, so they should work OK, plus they use a common wrench to install or remove. Overall a poorly designed setup.
UJM81
Comentado en los Estados Unidos el 23 de febrero de 2025
It took a couple of extra days to get these since I got a bottle of mascara instead of them. Once that was returned, they arrived the following day and were as described. They are a good selection for the cost, and will be helpful when I print with more abrasive filament.UPDATE- The Artillery X4 Plus uses a small diameter tip with small flat spots (maybe 4mm?) to remove it. The removal tool is only available through them, so it's a lengthy delay and high cost to get one. That should come with the printer. I found a 4-way lug wrench style of tool I had from another printer would work via the smallest opening, but I managed to break the thermistor when I tried to swap the nozzles. These nozzles are the same length and thread, so they should work OK, plus they use a common wrench to install or remove. Overall a poorly designed setup.
UJM81
Comentado en los Estados Unidos el 23 de febrero de 2025
It took a couple of extra days to get these since I got a bottle of mascara instead of them. Once that was returned, they arrived the following day and were as described. They are a good selection for the cost, and will be helpful when I print with more abrasive filament.UPDATE- The Artillery X4 Plus uses a small diameter tip with small flat spots (maybe 4mm?) to remove it. The removal tool is only available through them, so it's a lengthy delay and high cost to get one. That should come with the printer. I found a 4-way lug wrench style of tool I had from another printer would work via the smallest opening, but I managed to break the thermistor when I tried to swap the nozzles. These nozzles are the same length and thread, so they should work OK, plus they use a common wrench to install or remove. Overall a poorly designed setup.
UJM81
Comentado en los Estados Unidos el 23 de febrero de 2025
It took a couple of extra days to get these since I got a bottle of mascara instead of them. Once that was returned, they arrived the following day and were as described. They are a good selection for the cost, and will be helpful when I print with more abrasive filament.UPDATE- The Artillery X4 Plus uses a small diameter tip with small flat spots (maybe 4mm?) to remove it. The removal tool is only available through them, so it's a lengthy delay and high cost to get one. That should come with the printer. I found a 4-way lug wrench style of tool I had from another printer would work via the smallest opening, but I managed to break the thermistor when I tried to swap the nozzles. These nozzles are the same length and thread, so they should work OK, plus they use a common wrench to install or remove. Overall a poorly designed setup.
UJM81
Comentado en los Estados Unidos el 23 de febrero de 2025
It took a couple of extra days to get these since I got a bottle of mascara instead of them. Once that was returned, they arrived the following day and were as described. They are a good selection for the cost, and will be helpful when I print with more abrasive filament.UPDATE- The Artillery X4 Plus uses a small diameter tip with small flat spots (maybe 4mm?) to remove it. The removal tool is only available through them, so it's a lengthy delay and high cost to get one. That should come with the printer. I found a 4-way lug wrench style of tool I had from another printer would work via the smallest opening, but I managed to break the thermistor when I tried to swap the nozzles. These nozzles are the same length and thread, so they should work OK, plus they use a common wrench to install or remove. Overall a poorly designed setup.
UJM81
Comentado en los Estados Unidos el 23 de febrero de 2025
It took a couple of extra days to get these since I got a bottle of mascara instead of them. Once that was returned, they arrived the following day and were as described. They are a good selection for the cost, and will be helpful when I print with more abrasive filament.UPDATE- The Artillery X4 Plus uses a small diameter tip with small flat spots (maybe 4mm?) to remove it. The removal tool is only available through them, so it's a lengthy delay and high cost to get one. That should come with the printer. I found a 4-way lug wrench style of tool I had from another printer would work via the smallest opening, but I managed to break the thermistor when I tried to swap the nozzles. These nozzles are the same length and thread, so they should work OK, plus they use a common wrench to install or remove. Overall a poorly designed setup.
UJM81
Comentado en los Estados Unidos el 23 de febrero de 2025
It took a couple of extra days to get these since I got a bottle of mascara instead of them. Once that was returned, they arrived the following day and were as described. They are a good selection for the cost, and will be helpful when I print with more abrasive filament.UPDATE- The Artillery X4 Plus uses a small diameter tip with small flat spots (maybe 4mm?) to remove it. The removal tool is only available through them, so it's a lengthy delay and high cost to get one. That should come with the printer. I found a 4-way lug wrench style of tool I had from another printer would work via the smallest opening, but I managed to break the thermistor when I tried to swap the nozzles. These nozzles are the same length and thread, so they should work OK, plus they use a common wrench to install or remove. Overall a poorly designed setup.
BobJ
Comentado en los Estados Unidos el 1 de febrero de 2025
Bags are packed tight in the shipping box and are very wrinkled. I have bought several sizes of the bags and they all have to be ironed.
roxanne perkins
Comentado en los Estados Unidos el 30 de mayo de 2024
I used these for VBS. The kids LOVED personalizing them to carry the cool toys they collect during the week.
Donovan
Comentado en los Estados Unidos el 24 de mayo de 2024
I got these bags to use as goodie bags for my sons birthday and the came out exactly as wanted. Absolutely adorable and good size!
Charlene Yates
Comentado en los Estados Unidos el 10 de marzo de 2024
Has worked well so far but on of the .8 were missing but I would call that quality control and not the company's fault.
Charlene Yates
Comentado en los Estados Unidos el 10 de marzo de 2024
Has worked well so far but on of the .8 were missing but I would call that quality control and not the company's fault.
Charlene Yates
Comentado en los Estados Unidos el 10 de marzo de 2024
Has worked well so far but on of the .8 were missing but I would call that quality control and not the company's fault.
Charlene Yates
Comentado en los Estados Unidos el 10 de marzo de 2024
Has worked well so far but on of the .8 were missing but I would call that quality control and not the company's fault.
Charlene Yates
Comentado en los Estados Unidos el 10 de marzo de 2024
Has worked well so far but on of the .8 were missing but I would call that quality control and not the company's fault.
Charlene Yates
Comentado en los Estados Unidos el 10 de marzo de 2024
Has worked well so far but on of the .8 were missing but I would call that quality control and not the company's fault.
Charlene Yates
Comentado en los Estados Unidos el 10 de marzo de 2024
Has worked well so far but on of the .8 were missing but I would call that quality control and not the company's fault.
Charlene Yates
Comentado en los Estados Unidos el 10 de marzo de 2024
Has worked well so far but on of the .8 were missing but I would call that quality control and not the company's fault.
Megan
Comentado en los Estados Unidos el 13 de octubre de 2024
Quality overall is fine, but they are in ROUGH shape when they arrive. It doubled my project time trying to get all the creases out of them. You've been warned!
Customer
Comentado en los Estados Unidos el 26 de enero de 2024
If you need these for projects, order them well in advance because you'll probably have to iron every single one! Otherwise they're fine, loose threads and such but a good size and they seem sturdy enough
Joshua L. Ankney
Comentado en los Estados Unidos el 13 de abril de 2024
The only thing I wish that you didn't have to do is to heat up the extruder to remove and install a new nozzle. However, they fit it perfectly fine and I will recommend this to others in the future.
TIM F
Comentado en Canadá el 5 de abril de 2024
Great selection of different sized nozzles. There was a slight difference in Z height but a quick bed adjustment did the trick when changing my stock nozzle to these.There also doesn't seem like much variation in length/Z between these so swapping them for me only required a fine tune.They print just as well as the nozzle my, albeit inexpensive monoprice, machine came with.Very happy.
Joshua L. Ankney
Comentado en los Estados Unidos el 13 de abril de 2024
The only thing I wish that you didn't have to do is to heat up the extruder to remove and install a new nozzle. However, they fit it perfectly fine and I will recommend this to others in the future.
TIM F
Comentado en Canadá el 5 de abril de 2024
Great selection of different sized nozzles. There was a slight difference in Z height but a quick bed adjustment did the trick when changing my stock nozzle to these.There also doesn't seem like much variation in length/Z between these so swapping them for me only required a fine tune.They print just as well as the nozzle my, albeit inexpensive monoprice, machine came with.Very happy.
Joshua L. Ankney
Comentado en los Estados Unidos el 13 de abril de 2024
The only thing I wish that you didn't have to do is to heat up the extruder to remove and install a new nozzle. However, they fit it perfectly fine and I will recommend this to others in the future.
TIM F
Comentado en Canadá el 5 de abril de 2024
Great selection of different sized nozzles. There was a slight difference in Z height but a quick bed adjustment did the trick when changing my stock nozzle to these.There also doesn't seem like much variation in length/Z between these so swapping them for me only required a fine tune.They print just as well as the nozzle my, albeit inexpensive monoprice, machine came with.Very happy.
Joshua L. Ankney
Comentado en los Estados Unidos el 13 de abril de 2024
The only thing I wish that you didn't have to do is to heat up the extruder to remove and install a new nozzle. However, they fit it perfectly fine and I will recommend this to others in the future.
TIM F
Comentado en Canadá el 5 de abril de 2024
Great selection of different sized nozzles. There was a slight difference in Z height but a quick bed adjustment did the trick when changing my stock nozzle to these.There also doesn't seem like much variation in length/Z between these so swapping them for me only required a fine tune.They print just as well as the nozzle my, albeit inexpensive monoprice, machine came with.Very happy.
Joshua L. Ankney
Comentado en los Estados Unidos el 13 de abril de 2024
The only thing I wish that you didn't have to do is to heat up the extruder to remove and install a new nozzle. However, they fit it perfectly fine and I will recommend this to others in the future.
TIM F
Comentado en Canadá el 5 de abril de 2024
Great selection of different sized nozzles. There was a slight difference in Z height but a quick bed adjustment did the trick when changing my stock nozzle to these.There also doesn't seem like much variation in length/Z between these so swapping them for me only required a fine tune.They print just as well as the nozzle my, albeit inexpensive monoprice, machine came with.Very happy.
Joshua L. Ankney
Comentado en los Estados Unidos el 13 de abril de 2024
The only thing I wish that you didn't have to do is to heat up the extruder to remove and install a new nozzle. However, they fit it perfectly fine and I will recommend this to others in the future.
TIM F
Comentado en Canadá el 5 de abril de 2024
Great selection of different sized nozzles. There was a slight difference in Z height but a quick bed adjustment did the trick when changing my stock nozzle to these.There also doesn't seem like much variation in length/Z between these so swapping them for me only required a fine tune.They print just as well as the nozzle my, albeit inexpensive monoprice, machine came with.Very happy.
Joshua L. Ankney
Comentado en los Estados Unidos el 13 de abril de 2024
The only thing I wish that you didn't have to do is to heat up the extruder to remove and install a new nozzle. However, they fit it perfectly fine and I will recommend this to others in the future.
TIM F
Comentado en Canadá el 5 de abril de 2024
Great selection of different sized nozzles. There was a slight difference in Z height but a quick bed adjustment did the trick when changing my stock nozzle to these.There also doesn't seem like much variation in length/Z between these so swapping them for me only required a fine tune.They print just as well as the nozzle my, albeit inexpensive monoprice, machine came with.Very happy.
Joshua L. Ankney
Comentado en los Estados Unidos el 13 de abril de 2024
The only thing I wish that you didn't have to do is to heat up the extruder to remove and install a new nozzle. However, they fit it perfectly fine and I will recommend this to others in the future.
TIM F
Comentado en Canadá el 5 de abril de 2024
Great selection of different sized nozzles. There was a slight difference in Z height but a quick bed adjustment did the trick when changing my stock nozzle to these.There also doesn't seem like much variation in length/Z between these so swapping them for me only required a fine tune.They print just as well as the nozzle my, albeit inexpensive monoprice, machine came with.Very happy.
Productos recomendados
Mex $378.95
Mex $ 174 .00 Mex $174.00
Mex $598.00
Mex $ 322 .00 Mex $322.00
Mex $130.00
Mex $ 72 .00 Mex $72.00
Mex $245.00
Mex $ 134 .00 Mex $134.00
Mex $630.00
Mex $ 315 .00 Mex $315.00