No hay artículos en el carro
No hay artículos en el carro
Modelo compatible
Compatible con mini cooper f55 f56 hatchback 2014-presente
Hecho de vinilo KK de alta calidad con hasta 3 a 5 años de vida útil.
Fácil instalación, viene con calcomanía en la parte posterior.
Material respetuoso con el medio ambiente, no daña la superficie cuando se retira
El paquete incluye: capucha + kit de rayas traseras.
Consejo de instalación:
Paso 1: prepara la botella de escaso, trapo y raspador, para limpiar totalmente el área de aplicación.
Paso 2: despegar de la hoja inferior y dejar que la calcomanía permanezca en la película de transferencia.
Paso 3: Raspa el agua y las burbujas de aire de centro a esquina utilizando un raspador.
Paso 4: utiliza una pistola de calor, secador de pelo o encendedor para aplanar y fijar el lugar irregular.
Cheri M.
Comentado en los Estados Unidos el 30 de junio de 2024
The fit does not match oem sizing on the mini do not recommend replacing old original decals.
Stew
Comentado en Canadá el 23 de enero de 2023
Product came as promised, rolled up. Had to lay out and flatten for two weeks. Will put on once temperature gets up, will not work at -15 degrees and snow
Tammy reyes
Comentado en los Estados Unidos el 14 de agosto de 2021
Quality product very easy to do
fatima
Comentado en los Estados Unidos el 28 de noviembre de 2020
Clean the surface before applying, might need two people to apply :) I have gone through the car wash many times and they haven’t came off !!
Ryanbuc007
Comentado en los Estados Unidos el 13 de junio de 2018
The product arrived early and was packaged well. It is in a cylinder. Just unroll the stripes, set the product in the sun, and weight the end for an hour or so and it will lay flat. There is no white boarder around these stripes which I LOVE! They are of good quality and the application process was pretty easy. The only reason I am giving them 4 stars is that they do not fit on the car hood as shown in the picture. I wanted the stripes to be angled as shown, but when laid out, they were about 4-6 inches too short. When laid straight from grill to windshield they fit fine, which is how I ended up applying them.For the record, I have never applied a racing stripe or other decal to a car before. I just watched a few YouTube videos and went for it! To apply, I used a water bottle with a pump, filled it with water and added a few drops (like 5) of dish soap. I cleaned the surface of the car where the stripe is to be applied using the soapy water and paper towels. Then I wet the surface with the soapy water (wet it really good). The soapy water allows you to lift and reapply. After wetting the surface, remove the protective side of the stripe wrapping. Make sure the stripe stays on the clear transfer liner. Then, apply the stripe to the car. It's best to use 2 people to apply the stripe, keeping it tight while one person holds it a the grill and the other at the windshield. I had a 3rd person tell us if it was straight. Once aligned, I used a hard plastic spatula (from the kitchen) to firmly attach the sticker to the car hood and work out the bubbles. Not all bubbles will come out as there is soapy water underneath. Allowing the car to sit in the sun for a few days will allow the water to evaporate and then you can work the air bubbles out. I don't recommend puncturing the sticker as that will leave holes for water to get in and eventually it might make the un-adhered sections larger or the decal will fall off. Once firmly attached, remove the clear liner leaving the sticker on the car hood. Wipe clean and work out any of the larger bubbles that remain if you can. Then repeat on the backside if you want them.
Productos recomendados
Mex $418.46
Mex $ 209 .00 Mex $209.00
Mex $424.16
Mex $ 207 .00 Mex $207.00