No hay artículos en el carro
No hay artículos en el carrocaja de relé titular de relé caja de relé de fusibles caja de relé de fusibles y caja de relé de relé de 12 V caja de fusibles caja de relé de 12 V caja de fusibles impermeable automotriz caja de fusibles impermeable
Kevin M.
Comentado en los Estados Unidos el 14 de mayo de 2024
I have uses these on several projects. They are well built, customizable, have lots of options and are large enough the do alot, but small enough to tuck away. The terminals it comes with seem to be ok. I wish there was a HD brass or copper terminal option. I have mounted the majority of them laying flat. Where fuses and relays mount straight down. Only 1 I have mounted on edge (vertically) where it's possible the terminals could loosen up and relays or fuses vibrate or fall out. So far so good. The threaded lugs are an M5 course thread. I run a 50 to 70amp breaker protected battery + cable to one set and chain off of it to diffrent circuits. Another lug will be batt -. The 3rd I'll make a keyed power pulling via a constant duty solenoid triggered by the key switch. Have had one unit arrive with a damaged box and lid. Item was replaced promptly. This unit is NOT sealed. This unit is NOT water proof. Mount unit in cab or area water will not get it. Unit is flat mount. Terminals can accommodate 12 gauge wire if your careful crimping them. But terminals like 14 gauge better.
Customer
Comentado en Canadá el 31 de octubre de 2024
tres bien
Lynn R. Stevens
Comentado en los Estados Unidos el 1 de julio de 2023
I needed extra terminals I never get it right the first time. Still trying to match fuse terminal for exact fit. Used for rat rod built from scratch. If I can get more terminals , and a little more room for wires. I will rate it a 5
Old and Stiff
Comentado en Canadá el 1 de abril de 2023
If you are in need of a fuse and relay holder .. then this is the best product out there !The quality of the material is extremely robust and durable. The way it mounts is extremely solid. And the top-cover is very secure, and stll easy to remove.And this relay/fuse holder is attractive enough to be a show-piece, as I'd never hide this one !On the under-side are 7 super-solid brass distribution nodes, that you can use for your power distribution and for your grounds. Those brass power distribution nodes are a key feature for all your wire management, as you know .. a lot goes-on under there. They are the best solution ever ! for use with ring terminals.Each individual relay holder can be removed, rotated, relocated, and reorganized to suit your layout needs, whether you do a line or checkerboard layout .. this holder has you covered.Another great feature is all the spade and fuse holder crimps/tangs/lugs however you say them are supplied.Which gives you the freedom to use anywhere from 30 to 10 AWG wire In your project. Which is perfect for both power and your trigger wires.The fuse holders hold the ATC/ATO regular sized fuses.One of the best features is that you can reconfigure the fuse and relay-holder layout into any pattern you wish, as each 15 holders can be moved. And each individual fuse and relay holder can be rotated in any direction as well. Also, each Relay holder can hold all and any 1,2,3 4 and 5-pin relay, and any combination of pin orientation. Which is perfect for all Flasher relays as well.About the size .... it's amazingly compact, as I've seen bigger phones, and you can really fill this unit up, as it holds 10 Relays and 15 fuses.I can almost hide the entire unitunder one hand !And there is plenty of room for all your wires as well.There is even enough real-estate around the top perimeter for some switches to be mounted, as I used them for disabling the incoming power, and disabling the terminal 85 grounds.And this Seller is amazing !!!My lid was damaged in shipping, and they responded the same day,and express-shipped a entire replacement the next day. I am impressed to say the least. So-far .. this is my third unit. And I will buy more.My personal tip: I Install a relay/fuse holder in both the front and rear of every car, and use a negative trigger configuration.This methodology can reduce the gauge of wire in the entire middle of your car/boat/plane/buggy/dash, and give you a nicer finished vehicle.If you are here reading this review ... you've found the best, most universal, solid, durable, compact, attractive fuse/relay holder out there for sale !Cheers !
Ronald S.
Comentado en los Estados Unidos el 16 de diciembre de 2022
This fuse/relay block is awesome. Very well made. Takes a lot of work to wire everything up, but totally worth it. I soldered every connection. This is not weather/water proof at all, but it's perfect for my needs.
Productos recomendados
Mex $255.00
Mex $ 130 .00 Mex $130.00
Mex $276.99
Mex $ 160 .00 Mex $160.00