No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Makerzone - Sensor termistor de impresora 3D ohmios NTC 100K 3950 con cableado de 1 metro, conector de 2 pines
Tipo: Termistor NTC 3950. Longitud: 1 m/39.37 pulgadas. Sensor de temperatura 100 KΩ Precisión: +/- 1%. Temperatura de funcionamiento: -40 grados Celsius - +300 grados Celsius. Conector: 2 pines XH2.54.
ohm NTC 3950 100K Termistor compatible con Prusa I3 MK2S/Prusa I3 MK3/Prusa MK3S+ /Prusa mk3s cama calentada J-Head.
El conector está especialmente diseñado para la placa principal del driver MK3, así que comprueba antes de realizar el pedido.
Salderink
Comentado en los Estados Unidos el 16 de junio de 2024
First of all, I have to say I am no expert concering the Ender MK8 hotend. I wanted to end the "hairs" and "strings" that I had so many issues with on my Ender 3 V2 printer.After reading about the shortcomings of the MK8 hotend, I determined that I wanted to make some changes. Mainly, I wanted to install a bi-metal heatbreak to see if that would help. This led to changing the hot block for the Polisi3d copper block. I also felt that I could steady temps with a better thermistor setup. That led to this product. This installs perfectly into the Polisi block. I added the Bi-Metal heatbreak from Slice Engineering to round out the build. First print I watched the print from Octoprint and the max deviation in temps was .2C .If you have watched a standard hotend temps in Octoprint, you'll recognze the rollercoaster that the MK8 shows. Every subsequent print has duplicated these temps.I am running the Mriscoc firmware on a creality 4.2.7 mainboard.The cost of these thermistors makes them a 5 star in my opinion.
PROPHOTOSOLUTION
Comentado en los Estados Unidos el 18 de mayo de 2024
The product was a perfect fit for my Ender 3V2 and cable length did not fell short either. High quality and works as intended without mentioning easy installation.
Drake
Comentado en los Estados Unidos el 29 de febrero de 2024
Both of these have caused thermal runaway protection to trigger periodically. After a shutdown and reboot it will then report 60C above where it was set. When they don't fail immediately there is a lot of variation in temp and sometimes thermal failures hours later. Each was PID tuned as well.
Customer
Comentado en los Estados Unidos el 29 de agosto de 2023
This is the only brand I found that worked with the Ender 3 V2.Many other companies sell a thermistor that say they work with Ender 3 V2 but their cable is only 1 meter long. This product is 1.2m long and while it's about 2" shorter than the factory cable it works fine because there is a little extra in the control box from the factory. Remember to use a razor blade to cut the hot glue the factory installs on the existing cable to keep it in the terminal during shipping before trying to remove the factory cable.
Rich Downey
Comentado en los Estados Unidos el 19 de diciembre de 2023
Went thru a few normal Thermistors, then found these and they work great. A quick PID tune and all was perfect. Plus the quick release, BONUS!
Productos recomendados
Mex $299.99
Mex $ 137 .00 Mex $137.00
Mex $275.00
Mex $ 159 .00 Mex $159.00
Mex $547.14
Mex $ 262 .00 Mex $262.00