Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Ender-3/Ender-3-v2 Reemplazo de termistor: 4 piezas de 1,2 m de alta temperatura NTC 3950 100 K Ohm Sensor termistor para Creality Ender 3 V2 Neo/3 V3/3 Pro/Voxelab Aquila, fácil de

Envío gratis en pedidos superiores a Mex $600.00

Mex $282.63

Mex $ 144 .00 Mex $144.00

En stock

1.Nombredelestilo:Cabinet



  • Resistente y fiable: la impresora 3D ender 3 v2 está hecha de materiales de alta calidad con un sellado calcomanía de cerámica de alta temperatura, que puede proteger el termistor y prolongar su vida útil. Conducción de calor rápida, alta sensibilidad
  • Resistencia a altas temperaturas: este termistor ntc de medición de temperatura de 100 K es de hasta 300 ℃, puede reemplazar el sensor de temperatura original, se adapta a imprimir filamento de alta temperatura
  • Fácil de instalar: instalación sencilla, sin necesidad de herramientas complicadas. El reemplazo del termistor ender 3 tiene un conector estandarizado, fácil de conectar y salir, y se puede conectar rápidamente reemplazándolos directamente. Sellado e impermeable
  • Amplia compatibilidad: el termistor Ender 3 se utiliza para impresora 3D con calefacción o extremo caliente. como: Ender 3 Hotend, CR10 Hotend, adecuado para Creality Ender 3, Ender 3 v2, Ender 3 Pro, Ender 3 V2 Neo, Ender 3 V3, Ender 5, CR-10, CR-10S, Voxelab Aquila, etc
  • El paquete incluye: 4 sensores termistores NTC 100K ohm 3950 de 4 pies. Parámetros recomendados para el termistor: R25℃=100K B25/50=3950K± 1%, Conector: 2pin XH2.54
  • Nota: nuestro termistor Ender 3 no es compatible con la impresora 3D Ender 3S/CR-10S Pro V2/CR-10S Pro/Ender 2 Pro/Ender 6/Prusa i3. Mide la longitud del termistor de impresora 3D y asegúrate de su compatibilidad antes de comprar



Descripción del producto

Makerzone - Sensor termistor de impresora 3D ohmios NTC 100K 3950 con cableado de 1 metro, conector de 2 pines

Impresora 3D NTC 100K 3950 Sensor termistor

Tipo: Termistor NTC 3950. Longitud: 1 m/39.37 pulgadas. Sensor de temperatura 100 KΩ Precisión: +/- 1%. Temperatura de funcionamiento: -40 grados Celsius - +300 grados Celsius. Conector: 2 pines XH2.54.

ohm NTC 3950 100K Termistor compatible con Prusa I3 MK2S/Prusa I3 MK3/Prusa MK3S+ /Prusa mk3s cama calentada J-Head.

Impresora 3D NTC 100K 3950 Termistor Upgrade

El conector está especialmente diseñado para la placa principal del driver MK3, así que comprueba antes de realizar el pedido.

Sensor de temperatura NTC 100K

Impresora 3D NTC 100K 3950 Sensor termistor

Impresora 3D NTC 100K 3950 Sensor termistor


Salderink
Comentado en los Estados Unidos el 16 de junio de 2024
First of all, I have to say I am no expert concering the Ender MK8 hotend. I wanted to end the "hairs" and "strings" that I had so many issues with on my Ender 3 V2 printer.After reading about the shortcomings of the MK8 hotend, I determined that I wanted to make some changes. Mainly, I wanted to install a bi-metal heatbreak to see if that would help. This led to changing the hot block for the Polisi3d copper block. I also felt that I could steady temps with a better thermistor setup. That led to this product. This installs perfectly into the Polisi block. I added the Bi-Metal heatbreak from Slice Engineering to round out the build. First print I watched the print from Octoprint and the max deviation in temps was .2C .If you have watched a standard hotend temps in Octoprint, you'll recognze the rollercoaster that the MK8 shows. Every subsequent print has duplicated these temps.I am running the Mriscoc firmware on a creality 4.2.7 mainboard.The cost of these thermistors makes them a 5 star in my opinion.
PROPHOTOSOLUTION
Comentado en los Estados Unidos el 18 de mayo de 2024
The product was a perfect fit for my Ender 3V2 and cable length did not fell short either. High quality and works as intended without mentioning easy installation.
Drake
Comentado en los Estados Unidos el 29 de febrero de 2024
Both of these have caused thermal runaway protection to trigger periodically. After a shutdown and reboot it will then report 60C above where it was set. When they don't fail immediately there is a lot of variation in temp and sometimes thermal failures hours later. Each was PID tuned as well.
Customer
Comentado en los Estados Unidos el 29 de agosto de 2023
This is the only brand I found that worked with the Ender 3 V2.Many other companies sell a thermistor that say they work with Ender 3 V2 but their cable is only 1 meter long. This product is 1.2m long and while it's about 2" shorter than the factory cable it works fine because there is a little extra in the control box from the factory. Remember to use a razor blade to cut the hot glue the factory installs on the existing cable to keep it in the terminal during shipping before trying to remove the factory cable.
Rich Downey
Comentado en los Estados Unidos el 19 de diciembre de 2023
Went thru a few normal Thermistors, then found these and they work great. A quick PID tune and all was perfect. Plus the quick release, BONUS!
Productos recomendados

Mex $781.77

Mex $ 390 .00 Mex $390.00

4.9
Elegir

Mex $570.01

Mex $ 290 .00 Mex $290.00

4.7
Elegir