Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Equipo de extrusora de impresora 3D mejorada y brazo loco con ranura para Titan Aero Prusa i3 Ultimate Artillery Hornet Sidewinder X1 X2 Genius/Pro Extrusora de piezas (negro)

Envío gratis en pedidos superiores a Mex $600.00

Mex $199.00

Mex $ 111 .00 Mex $111.00

En stock

1.Color:Negro -


  • Brazo extrusor de metal inactivo: la vida útil del plástico es de aproximadamente 3 a 6 meses, nuestro brazo loco está hecho de aluminio, mucho más fuerte que el plástico.
  • Rodamiento mejorado: el centro del rodamiento con ranura, que es beneficioso para apretar el filamento, especialmente filamento suave como TPU, nunca deslizar. El otro rodamiento mantiene el motor paso a paso, suave.
  • 【Equipo grande de plástico de 66 dientes】Este equipo extrusor está hecho de plástico (POM) y material inoxidable, que es ampliamente utilizado en el campo industrial, lo suficientemente fuerte para alimentar filamento. Con 66 dientes, que se tratan sin rebabas, que pueden enganchar el filamento suave y silenciosamente.
  • Funciona para filamento de 1,75 mm: funciona para filamento PLA ABS TPU de 1,75 mm, no para filamento de 3 mm.
  • Compatible con: se puede utilizar en la extrusora Titan Aero Prusa i3 Ultimate Artillery Hornet Sidewinder X1 X2 Genius.


Lista de embalaje:
1 soporte de brazo de metal.
1 equipo de plástico negro


Noname
Comentado en Italia el 14 de marzo de 2024
Sono molto soddisfatto. La stampante finalmente ha un buon mordente al filo della bobina, cosa importantissima per non aver problemi di stampa. Purtroppo l'originale, in plastica, prima o poi inevitabilmente si mangia....Piccola nota e consiglio, ho riciclato ed usato la molla originale che fà fare più presa in quanto è appena più lunga.
Anders
Comentado en Alemania el 1 de marzo de 2024
Rugged and sturdy. No problem to install. Way better than the plastic oneI highly recommend this if you want more even extrusion
JLVW
Comentado en Canadá el 5 de noviembre de 2023
Idler bearing fell apart after a few prints and jammed, complete junk. Arm itself is of good quality, but idler won't idle after bearing jammed and therefore printer can't extrude filament.
PABLO GLEZ
Comentado en México el 26 de noviembre de 2023
Muy buen producto y excelente calidad
Joan Astals
Comentado en España el 29 de enero de 2023
Que las 2 ruedecillas están dentadas y eso empuja mejor
Jordan
Comentado en los Estados Unidos el 1 de mayo de 2022
This is a good replacement set for a real Titan. However! These gears and lever work with the genetic Titan but will require and additional item and a little work. I have replaced entire China titans more times that I can mention but reason it usually due to worn arm or worn feed gear as after a few hundred hours the gear teeth get worn down. You can file them to get a little more bite but this gear set is the answer. You WILL need 5mmx10mmx3mm bearings to make this work as the shafts on this gear are smaller than the china ones. There is no 5mmx10mmx3mm bearings. So your choice is 5mmx9mmx3mm these will fit this gear perfect but not the hole in the china plastic frame. They are 1mm to small so your gear will wobble. It WILL work if your tighten the thumb screw for tension really tight. Or if you find or print a 1mm shim. Or you can go with 5mmx10mmx4. This best choice. As it fits the hole and the shaft perfect but sits out about .5mm to far I used a solder iron to heat bearing and push it further into the plastic or you could remove some of the plastic to make it work. Now for about 15$ you have real hardened Titan gear metal arm and better bearings in your genetic Titan. I highly recommend the metal arm and the hobbled gear. This is good quality set. I’m buying 5 more.
Productos recomendados

Mex $129.00

Mex $ 64 .00 Mex $64.00

4.9
Elegir

Mex $256.46

Mex $ 130 .00 Mex $130.00

4.5
Elegir