Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Gizmo Dorks PEI Sheet 3D para impresora de superficie de 310 mm x 320 mm, compatible con CR-10S Pro o Pro V2, fabricado en los Estados Unidos

Envío gratis en pedidos superiores a Mex $600.00

Mex $431.64

Mex $ 228 .00 Mex $228.00

En stock

Acerca de este artículo

  • Fabricado en los Estados Unidos: la lámina Ultem 1000 PEI se instala rápidamente a través del calcomanía laminado en la parte superior de las plataformas de construcción plana existentes (por ejemplo, vidrio de borosilicato)
  • Aplicación sin burbujas: el calcomanía 3M 468MP ya está preaplicado al PEI; simplemente retira el forro de cinta para una rápida adhesión a la cama
  • Superficie de construcción: PEI es la superficie de construcción perfecta sin preparación que es infinitamente reutilizable para múltiples impresiones; limpia con alcohol isopropílico entre impresiones (o con acetona en una cama fría)
  • Los filamentos ABS y PLA (junto con muchos otros materiales) se imprimen directamente en la superficie PEI sin la necesidad de adhesivos, cintas o lechada adicionales
  • Dimensiones PEI: 310 mm x 320 mm x 0,56 mm. Grosor del calcomanía laminado 3M 468 MP: 0,13 mm. Se adapta perfectamente a las impresoras Creality CR-10S Pro v2, Ender 3 Max y otras impresoras


Instalación:

La lámina de Polieterimida (PEI) viene con adhesivo 3M 468MP ya laminado al PEI. Aplicar el PEI con presión y en ángulo para evitar y minimizar las burbujas de aire. Una vez aplicado, ajuste la cama de impresión a 60 C y aplique presión uniformemente a través del PEI de una manera barrida para fijar firmemente el adhesivo. Utiliza una toalla para evitar quemarse. Nivelar la cama y establecer la altura de la boquilla antes de imprimir.

Si PEI está instalado en la superficie superior de un sándwich de cama (una placa de construcción con varias capas), se recomienda instalar PEI en la parte superior del vidrio de borosilicato.

Uso:

Calentar la cama a las temperaturas deseadas para imprimir (60 C para PLA y 100 C para ABS). Dependiendo de lo grueso que sea su sándwich de cama, su temperatura establecida puede no ser su temperatura de PEI superficial.

Deja que la pieza se enfríe y la impresión será fácil de liberar de la superficie PEI. Las piezas son realmente más fáciles de quitar si se liberan antes de que la cama se vuelva completamente fría.

Nivelar la cama es muy, muy importante cuando se usa PEI. La primera capa debe aplastarse un poco. PETG es una excepción y no le gustan las capas aplastadas, en cuyo caso se debe usar una brecha Z.

Mantenimiento

Limpiar entre impresiones con alcohol isopropílico. La acetona se puede usar en lugar de alcohol isopropílico, pero debe usarse en una cama fría. El lijado ligero con papel de lija de grano 600 se puede hacer después de un montón de impresión para dar a la hoja PEI más vida.

Compatibilidad:

El volumen de construcción y el tamaño de la cama no siempre son los mismos! Esta hoja PEI se adapta con precisión a las siguientes impresoras.

Creality CR-10 V2 / Creality CR-10S Pro / Creality CR-10S Pro v2 / Creality CR-X / y mucho más. El PEI se puede cortar a medida mediante la puntuación con un cuchillo de pasatiempo.

Dimensiones:

310 x 320 mm.
Grosor PEI: 0,56 mm.
Grosor adhesivo 3M 468MP: 0,13 mm.


Kindle Customer
Comentado en los Estados Unidos el 23 de febrero de 2024
I had persistent issues with prints "welding" to the stock BuildTak build surface on my Raise3D Pro 2. I went through quite a few in just a few months, generally after ripping the surface with a scraper in a desperate effort to get a print off. I tried so many things from printer leveling, to exhaustive tweaking of filament settings. Frustrated, I decided to give the Gizmo Dorks PEI Sheet a go. Wow - what a difference. It's like magic: firm hold on prints during printing, and then magic release once the bed cools down. And the quality of layer 1 is stunning - it's glossy with no evidence of lines - doesn't even look like the product of a 3D printer!
SecretGarage
Comentado en México el 28 de marzo de 2023
El acabado que deja en la primera capa es super bueno
WagZ
Comentado en los Estados Unidos el 18 de marzo de 2023
No se pudo cargar el contenido.
MidnightRunner
Comentado en los Estados Unidos el 10 de diciembre de 2020
I'm a big fan of PEI sheets for 3D printers, they just work. Gizmodorks makes good ones too (I have them on 2 printers). PEI works best for PLA, but also works for PETG, and I have used them with ABS (not this one however). PLA requires nothing, just print normally and the print will stick and pop off when it cools. For PETG, I find that it can stick a bit too well (I use 60°C), but it is usually not a problem unless there is a large surface area that will stick to the bed, and then I hit it with some hairspray as a release agent. One of the benefits of a thick PEI sheet like this, is that you can easily hit it with scotch brite or sandpaper to clean it up, but that does have the downside of dulling the shiny finish. I prefer a bit of a matte finish though anyway. One tip though - when you install these, if your printer has rounded corners, I'd recommend rounding the corners on the PEI sheet as well, since they are sharp and bumping into one can have negative consequences for your knuckles (or so I have heard).
Steven H.
Comentado en los Estados Unidos el 10 de septiembre de 2020
I've been using a CR-10S for a while now and always used the stock glass bed that came with it. I would just go apply some childrens glue to the bed before doing a print to get good bed adhesion. But I was getting rather annoyed with this process. I have my printer set up to be controlled by octoprint and monitored through a webcam, so it was extremely annoying to have to go in there every time and apply glue after the bed and hot end is already heated before I could remotely send and start a print. If I applied the glue before heating the glue would dry by the time everything heated up and not give good adhesion.This PEI sheet has solved my problems amazingly. No bed prep whatsoever and so far 10 prints have stuck perfectly. And after a print when the bed cools removing the print is very easy. I don't even need to use any tools like I did with the glass and glue method. Plus the glue method would sometimes leave a very messy looking finish, with the PEI it's a nice glossy finish every time.If this product holds up it will probably be one of the best upgrades I've ever done on my 3d printer. It's cheap enough also that replacing it occasionally shouldn't be that big of a deal, but I'm a little worried about how hard the old sheet will be to get off if that time comes lol.
Bryan Jones
Comentado en los Estados Unidos el 20 de abril de 2020
I've been "suffering" bed adhesion a lot lately, to put blatantly simple. Truth be told, I saw this coming, it's common for men my age to experience issues in the bed but after doing a lot of research online and through the elimination of other supplements I came to this product, and thought "Hey its twenty dollars, its worth a shot I guess". Wham, bam, shang a lang, and a little bit of sha-la-la-la-la later and this arrives at my front door, packed well and all. Needless to say, my excitement was rising in more ways than one.Up the stairs I go, my face brim-full with childish glee as I eagerly unwrap the present delivered to me by the amazon god in the sky, and I race to take off my current print surface as fast as I can. I set up my slicer for the proper heat settings for this bed (70c) and get a nice little torture test ready to print, to see if this bed experience will meet up to my unreasonably high expectations.As soon as I started the print, my hopes and dreams were shattered faster than a highly infective virus can spread. I stared in total disappointment as I saw the melted plastic sticking to everything on my printer except for the bed, where it should be sticking but I've been let down before in life, I won't let a silly little printer bed beat me harder than every grade school teacher in my life.One ant-man later as I was pondering at what point in my life did I go wrong, and I look over at the bed, it staring at me with its laughing gaze, as if it was taunting me and all my failures in life. I take another look at the surface and get mad because it isn't even clear as pei should be, yet it had a slightly blue tinge to it. "What's one more problem to add to this terrible product," I think to myself as I whip out my phone to leave a disparaging review on this product, and in a fit of my rage I take my anger out on the bed surface. I scratch it with my fingernails and to my surprise, a sort of film-like material scrapes off with my abhorrently long quarantine nails, and then, like a wrong way truck going 80, it hits me. I forgot to take off the protective film.Anyways after a few prints later this product amazes me with how well it can hold on to molten plastic that has never liked to stick to anything on my printer in while, if you cant get your print to stick this works well. I've seen some people say to sand it but I haven't needed to, and I've been printing objects with more islands (small surfaces on the object that don't stick to beds well) than the Philippines and it prints amazingly. I'll leave below some handy temperatures to help if you'd like them.Pla: 70-75 degreesAbs: 105-110 degreesNylon: who in their right mind prints nylon on this printer, it's such a terrible idea, dear god don't do it.I did take a star off what would've been a perfect five-star review because in the fit of rage I had earlier, my wife left and took the kids with her and I haven't heard from her since, but ill update when that situation changes. Also because it's really easy to get air bubbles in the adhesive when you apply it to your printer so be careful on that part too.
Productos recomendados