Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Jiayouy - Comprobador de oscilador de vidrio de 1 Hz-50 MHz, kit de luces LED para manualidades

Envío gratis en pedidos superiores a Mex $600.00

Mex $348.13

Mex $ 177 .00 Mex $177.00

En stock
  • Alta resistencia a la abrasión, resistente y duradera, carcasa transparente que protege eficazmente el cuerpo de los contadores de frecuencia.
  • Ajuste programable de frecuencia de suma y resta para la medición de transceptores de radio y otros equipos.
  • Conversión automática de rango, sin interruptor humano; puede medir el vidrio de frecuencia de oscilación más utilizado.
  • Se puede seleccionar el modo de ahorro de energía. Si la frecuencia no se cambia automáticamente en 15 segundos, la visualización se cerrará automáticamente.
  • El rango de fuente de alimentación es amplio, que puede ser alimentado por interfaz USB de motores generales, o batería de 5-12 V o 9 V para fuente de alimentación externa.


Rango de frecuencia de medición: 1 Hz ~ 50 MHz. Frecuencia de señal: máx. 30 V. Batería: 1 batería de 9 V (no incluida). Fuente de alimentación: USB/alimentación externa (5 ~ 12 V). Color: amarillo. Material: PCB. Tamaño del acrílico: placa PCB: largo x ancho x profundidad: 6,3 x 4,9 cm. El paquete incluye: 7,3 x 5,8 x 1,7 cm. 1 kit de comprobador de frecuencia de bricolaje, 1 cable USB. Nota: la batería no está incluida. - Por favor, consulte las medidas. Puede haber un pequeño error de medición en el rango normal. - Puede haber un poco de diferencia de color debido al monitor, cámara u otros factores, consulte el artículo físico.


Michael Lloyd
Comentado en los Estados Unidos el 11 de enero de 2025
Likes: all the parts were in the package. The board is a simple old school design with lots of room. The transistor footprints were huge, like 1980's huge, but there was no problem with installing any component.Dislikes: The case is nice but the length of the screw (170mm) supplied screws is exactly the same as the outside to outside measurement of the case. You can't install a nut on the screws because there are no threads. The same applies to the short screws (60mm) that appear to be supplied to hold the board down.
T. L. C.
Comentado en los Estados Unidos el 17 de enero de 2024
Nice board! Not so nice “instructions” Totally horrible hardware (both sets of screws were too short to be usable)
P. S.
Comentado en los Estados Unidos el 31 de marzo de 2023
I bought this as I wanted a frequency counter, something descriptions and reviews assured me this would do.I excitedly received my package and instantly tore into it.Assembly was straightforward and uncomplicated.Upon completion and application of power, I was rewarded with a pretty seven segment display, but it didn’t do anything of recognizable value.Exposure to all manner of RF well below its maximum frequency range did nothing to change the display and it certainly was not displaying the RF frequency applied.I will most likely stupidly buy another in stupid hope it might work second time around.It might require a third attempt as we all know, third time’s the charm!Oh yeah, I forgot the gratuitous comment on my soldering ability!I am well educated and most of career has been spent in positions with the title of Engineer.I have held an amateur radio license since 1977 and consider myself skilled at such things as soldering and electronics assembly and to a degree, design engineering. I doubt it was my lack of skills or ability that prevent this device from functioning.DE WD9HRP
Kelly A. Burton
Comentado en los Estados Unidos el 18 de mayo de 2022
Was easy to put together. The docs were clear enough to figure out what went where. Fired it up and it worked first time. Nice that it comes with a barrel to USB plug, however most of us probably have a bench supply, so I did not use it. The only downside was no instructions for programming it, however other reviews have shown how to do this. Packaging could have been a little better, all the parts tossed in the bag, so some pins were bent, but easily fixed for installation on the PCB.
Dan Martin
Comentado en los Estados Unidos el 15 de mayo de 2022
Excellent product for the price. I repair old tube transceivers and... I thought I had a bad heterodyne crystal (18.275mc). Well, thanks to this baby I was proven incorrect and it's on to more troubleshooting for that radio.I slapped this tester/counter together in an afternoon over a couple of beers. The top reviews are pretty honest- The instructions are pixelated and the mounting doesn't really work with the component lead "teets" poking out from the underside... I used longer mounting screws and some extra hex nuts for standoffs- The circuit board has enough clearance from adjacent traces to allow for conductive standoffs.There was a comment or two on modifying the power supply, which I didn't really get. This tester needs 5v and comes with a USB power cable... your standard cellphone "wall wart" will foot the bill (double check- output voltage is usually 5V to USB connections).Anyways, the tester deserves five stars for the $15 price tag. You can build the whole thing off of the component schedule. I would advise checking resistors with a ohmmeter during assembly, but the taped component assortment makes it pretty obvious.
Productos recomendados

Mex $4,951.32

Mex $ 1,881 .00 Mex $1,881.00

4.5
Elegir

Mex $113.00

Mex $ 64 .00 Mex $64.00

4.7
Elegir