No hay artículos en el carro
No hay artículos en el carro Material: Plástico
Color: negro.
Características:
1. El interruptor de flotador es un dispositivo utilizado para detectar el nivel de líquido dentro de un tanque.
2. El interruptor puede accionar una bomba, un indicador, una alarma u otro dispositivo.
3. Se puede convertir fácilmente de normalmente abierto a normalmente cerrado por invertir el flotador.
Nota: debido a que la corriente que el interruptor puede transportar es muy pequeña (0,5 A), debes utilizar un relé o contactor cuando esté conectado por una carga, relé y contactor no están incluidos aquí.
Contenido del paquete: 6 sensores de nivel de agua
Gabi
Comentado en los Estados Unidos el 20 de febrero de 2025
looks good
Hanny
Comentado en los Estados Unidos el 13 de abril de 2025
Muy lindo., pero el adhesivo que trae no lo sostiene bien, se cae. El diseño se ve muy bonito y no es tan pequeño.
Angela Jackson
Comentado en los Estados Unidos el 27 de agosto de 2024
These are very cute, but kinda flimsy and kinda thin, but over all I think a good value for the price. The frame is made of cardboard so we will see how they hold up in a steamy bathroom. Easy to place, just use the provided double sided tape. Prior reviews said they don’t stay up well, but it’s been over 48 hours and they are still hanging on strong. God versatility since u can place them how ever u like and they are a pretty good size for a bathroom.Edit: these did eventually start to fall off the wall. I just got some clear flat push pins that easily went through the frame and into the wall and just added a cute extra detail, and no more falling.
Javier
Comentado en México el 2 de agosto de 2024
Están muy bonitos y quedan muy bien. Se sienten de buen material.
Claudia Aragon
Comentado en México el 3 de febrero de 2024
No sirve es puro papel
K B
Comentado en Canadá el 25 de agosto de 2023
The pics were cute and look great in the kids’ bathroom. However, with humidity, the corners unstick from the walls. Might look into putting them in frames.
Geras
Comentado en México el 24 de julio de 2023
Tamaño y calidad excelente, imágenes geniales y divertidas
xyz
Comentado en los Estados Unidos el 13 de mayo de 2023
I bought these to use and when they arrived, they were about twice as big as I was lead to believe, and so of no use to me. Other reviewers would have given these a 1 star rating and complained that they were too big. Just because they were too big for me has no bearing on the quality of the product, just the information on the site.
Victor Salazar Perez
Comentado en México el 21 de marzo de 2023
Muy buenos, hasta el momento sin fallas
Goddess Beauty
Comentado en Canadá el 6 de septiembre de 2023
Does come with paper framesLooks amazing in bath room
Jorge Saldivar
Comentado en México el 14 de septiembre de 2023
Muy bonitos quedan muy bien para decorar el baño, lo único es que se sienten muy frágiles como de baja calidad
Peter Sarossy
Comentado en los Estados Unidos el 9 de julio de 2022
The sensors themselves work great so far and seem reliable.There are no instructions on how to properly install this so I had to dig around and look at other similar products and installation photos to figure it out. The photos show the silicone gasket backwards from what actually works. The flange goes on the inside, through the hole, then the nylon washer goes on, then the nut. These create a watertight seal on both sides.
matt m.
Comentado en los Estados Unidos el 31 de mayo de 2022
Works well for flood sensor on jobs. Just make sure you check continuity. Have had a couple bad out of the package.
Chris Brown
Comentado en los Estados Unidos el 24 de febrero de 2022
Works great with Arduino to control nutrient solution levels in hydroponic system. digitalRead(A0); returns "1" or "0." For my application, as sensor falls, a "1" is sent to the Arduino, which charges a DC-DC relay to activate normally closed solenoid valve until signal reads "0" again. I was hesitant to order after reading a lot of the reviews that insisted they go out after a short while, until I more closely examined the reviews. You cannot wire these directly between a source and a load (over about 5v) or they will predictably burn out! They are sensors, not switches, and as such must be "read" by another device that is then able to act upon it. As at least one other reviewer has noted, Arduino is a simple and safe platform for reading the signal and causing some other action based on the state of the sensor. If you need more info, Youtube it - "Arduino float switch"
GM2013
Comentado en los Estados Unidos el 16 de octubre de 2022
Very simple reed switch. So far, all of them work great. The supply an input to a microcontroller. These are very low current switch, keepnthat in mind. If you are looking to directly use it as an inline switch, I would suggest using it to feed a MOSFET or opto-isolator. I would recommend using a SCR if it is for AC current
Productos recomendados
Mex $1,050.00
Mex $ 577 .00 Mex $577.00
Mex $500.52
Mex $ 275 .00 Mex $275.00