Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Módulo de sensor de rango ultrasónico RCWL-1601, compatible con HC-SR04, 2,2 mA, voltaje ancho, 3 V, 5 V

Envío gratis en pedidos superiores a Mex $600.00

Mex $270.01

Mex $ 137 .00 Mex $137.00

En stock

Acerca de este artículo

  • RCWL-1601 es un módulo de rango ultrasónico abierto
  • Punto ciego ultra pequeño de 2 cm, rango típico de 4,5 m más lejano
  • Voltaje de fuente de alimentación de 3 V-5.5 V, corriente de trabajo ultra baja de 2.2 mA
  • Alta precisión en la medición de algodón y objetos irregulares
  • 40 x 18 mm de tamaño más pequeño


Parámetros del producto
Voltaje de funcionamiento: 3 V ~ 5,5 V.
Corriente de trabajo: 2,2 mA.
Distancia máxima de detección: 400CM~450CM
Frecuencia de trabajo: 40KHz
Punto ciego: 2-3 cm.
Precisión de detección: ± 2 %
Resolución: 1 mm.
Error: ± 0,5 cm.
Ángulo de detección: ± 15 °~± 20 ° (ángulo direccional máximo).
Tiempo del ciclo de medición: 50 mS.
Modo de interfaz de salida: GPIO
Temperatura de trabajo: -10 ℃ ~ 60 ℃
Temperatura de trabajo: -10 ℃ ~ 90 ℃ (sonda de carcasa de aluminio)


Dachshund Digital
Comentado en los Estados Unidos el 26 de enero de 2025
They work... but zero documentation
Hisham Ragheb
Comentado en los Estados Unidos el 4 de junio de 2024
Bought those since the one came with my RexQualis training package was malfunctioning and producing constant readings. Those work perfectly fine. Satisfied with this purchase
Tony Campati
Comentado en los Estados Unidos el 8 de enero de 2024
I haven't been able to test these yet, but they appear to be well made. The soldering and components all appear to be pretty good and the pins are a good length. I'll update once I have played with them a bit.
Staple
Comentado en los Estados Unidos el 25 de enero de 2024
So with these ultrasonic sensors they often come requiring 5v. This one operates at 3.3v to 5v and that means you can connect it directly to your ESP chip without having to use resistors to drop the voltage back down to 3.3v.In my case I used an ESP 32 and wired it directly the the 3.3v rail, ground and two GPIOs. While it is not the HC-SR04, I was able to use it just as if it was and wire it without resistors. It worked just fine and there is no risk of burning out the GPIO since it is the standard 3.3 volt.Accuracy wise, it is about what your would expect for this type of sensor. Good for measuring distances to stationary or objects that move consistently closer or further away. I would not recommend this to replace a motion or beam sensor. It would be perfect for measuring a liquid level.
Productos recomendados

Mex $369.00

Mex $ 169 .00 Mex $169.00

4.5
Elegir

Mex $500.00

Mex $ 240 .00 Mex $240.00

4.8
Elegir

Mex $174.00

Mex $ 100 .00 Mex $100.00

4.4
Elegir