No hay artículos en el carro
No hay artículos en el carroEl kit profesional Magigoo está diseñado para uso profesional, para trabajar exclusivamente con filamentos de nylon, prolypropylene, policarbonato y ABS para adherirse a la construcción de una placa de una impresora 3D. La pieza debe ser relativamente fácil de quitar una vez que se enfríe.
Matthew K. Wimmer
Comentado en los Estados Unidos el 11 de febrero de 2025
Let's get this out of the way: Magigoo is not cheap. However, it does what it claims. The results with the PP and PC adhesion modifiers especially are quite impressive. If you've ever printed with PP or PC you know they can be a real $&+@ to get to adhere to the bed. This stuff makes it, I won't say "easy" because warping can still pose a problem with PC, but much less difficult. Cleanup is easier than tapes and films, as is application, thanks to the high quality applicator tubes. The 4 tube kit is nice in that you get everything in one package, and if you are experimenting with exotic filaments they're great to have on hand if the price doesn't put you off. I can absolutely recommend single tubes for targeted use. Does what it says on the tin.
Casey Hill
Comentado en los Estados Unidos el 2 de abril de 2025
If you are going to dive into the world of ABS,ASA,PA, you really need this. Without something like this, chances are you are either going to have not enough adhesion or too much and ruin your print bed trying to pry off parts. This stuff hits the sweet spot.
Fa. Adoma GmbH
Comentado en Alemania el 14 de marzo de 2024
Sehr gute Abwicklung, gerne wieder.
Pepe
Comentado en los Estados Unidos el 29 de diciembre de 2023
Hello there,I'm not an expert, which may be why you may find this review helpful. You don't have to be an expert to improve your printing skills with slightly more exotic materials than PLA.In the photos I'm sharing, I use Clear Polycarbonate and Black Tough PLA—both original filaments from Ultimaker, which requires two of the four included versions of Magigoo. I also tried the PP one with similar good results.With my PC, I also use Aquasys 120 water-soluble supports, the golden color you see in the photos, and it works just as well.One of the advantages is that it helps promote adhesion and helps a lot more with releasing the part once the printing bed cools down. Magigoo became my default go-to adhesion promoter in my printing because it is easy to use and more accessible to release after cooling. Both are important when you are using a glass printing bed.Yes, I tested other brands with mixed results. So far, I like the Magigoo experience better, but your mileage may vary. I also have a Carbon X1 printer that I don't use very often. I prefer the Magigoo standard to the original glue because this one is better.Thanks for reading!
NickJ
Comentado en el Reino Unido el 6 de noviembre de 2021
After seeing many youtubers rave about magigoo I decided to go all out and get their "pro" pack.The first thing that struck me was that why did I need so many different adhesives for the different types of filament. When most of them belong to the same family of polymers...After trying with PLA the adhesion was decent, but on larger models it does peel up around the edges. Performance with ABS and ASA was pretty bad with even small models curling.I was printing on FR4. Now you might say that its the bed surface that is at fault... but my normal go to adhesive is Dimafix in the pen form which sticks flawlessly to FR4, glass PEI everything. And you only need the one pen, it works with almost all materials, though sometimes its a bit flaky with nylon.So I have a bit of a bad taste in my mouth. For the cost I paid for this "pro" pack I could have bought 6 dimafix pens and I wish I had. Sadly they dont sell them on amazon, but you can get them from the e3d store. Save your money and dont waste your cash on this junk.
Productos recomendados
Mex $388.00
Mex $ 205 .00 Mex $205.00
Mex $1,132.11
Mex $ 532 .00 Mex $532.00
Mex $249.00
Mex $ 129 .00 Mex $129.00