Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Placa de construcción de impresora 3D de resina para Anycubic Photon M3, 2 hojas de acero de resorte flexible y 1 base magnética para plataforma de impresora 3D de 172 x 110 mm

Envío gratis en pedidos superiores a Mex $600.00

Mex $477.00

Mex $ 262 .00 Mex $262.00

En stock

1.Tamaño:Photon Mono 2 (160x94mm)


  • Modelos compatibles: la placa de construcción flexible de 172 x 110 mm es compatible con Anycubic Photon M3. Esta placa de construcción de acero también se puede utilizar con otras plataformas de impresión de tamaño similar. Asegúrese de medir la compatibilidad de su plataforma.
  • Contenido del paquete: el paquete incluye 2 placas de construcción flexibles (grosor: 0,5 mm) y 1 base de calcomanía magnético (grosor: 2 mm). Si encuentras algún problema de calidad, no dudes en ponerte en contacto con nosotros. Responderemos y resolveremos el problema lo antes posible.
  • Método de instalación: limpia y seca la plataforma de impresión a fondo. Fija la base magnética y déjela reposar para una adherencia óptima (preferiblemente durante más de 24 horas). Luego, instala la placa de acero de resorte. Por último, restablece y nivela la impresora. Se recomienda imprimir unos espaciadores de 3,8 mm de grosor para facilitar la puesta a cero adecuada del eje Z.
  • Alta durabilidad: la placa de acero flexible, con alto contenido de cromo para mayor durabilidad y prevención de óxido, es fácil de doblar y limpiar. Su superficie cepillada mejora la adherencia para impresiones perfectas. A diferencia de las plataformas tradicionales, esta placa flexible permite una fácil extracción del modelo doblándose, minimizando los daños en la
  • Diseño ergonómico: la plataforma de impresión magnética incluye un mango ergonómico para una fácil instalación y extracción, asegurando un funcionamiento suave. Este diseño fácil de usar reduce el riesgo de daños en la impresión durante la extracción, y la base magnética proporciona una fuerte adherencia para mantener los modelos seguros durante la impresión.



Descripción del producto

1
2
3
4
5
1

Kaidan R.
Comentado en Canadá el 29 de diciembre de 2024
If you're new to 3D printing, do not buy this product. The magnetic plate holds onto the build page very strongly and does its job well and the build plate sticks to it very well. But here's where the problem lies. So when zeroing my 3D printer it forced the the threaded beam to try to push the build plate down further than it needed to to zero so I could level it. The magnet is very thick. Issue number two when I tried running a test print after having it all set and leveled it did this a second time. Well I was printing. Luckily the FEP did not break. Issue number three the build plate itself it looks brushed this is a lie. The only way to get it brushed enough or textured enough for there to be good. Build adhesion is to essentially destroy the plate by sanding it with extremely coarse sandpaper which would void your ability to return it. So in order to get this product to work, you basically have to waive your rights to return it. Do not purchase.
james a currie
Comentado en Canadá el 23 de diciembre de 2024
I tried to use this product and even though I set the build height it almost cracked my screen. It is too thick and it was pushing down and wearing the motor. I had to turn it off. I wasted resin trying to set it up and almost broke my printer. I wasn't sure what would break first the screen or the motor. BAD PRODUCT!!!DONT BUY
TC Mom
Comentado en los Estados Unidos el 26 de noviembre de 2024
I got this for my son to use with our Anycubic Mono 4K 3D printer. It makes it a lot easier to remove the print.
MIKE
Comentado en los Estados Unidos el 25 de septiembre de 2024
Super easy to install as it says BUT, make sure you print off a spacer beforehand. i really feel they should make that instruction more apparent and/or provide you with the premade spacer or spacer file. i got this for my Photon Mono 2, and honestly forgot that i needed a spacer and nearly broke my resin printer screen when i went to level it. the build plate and magnet add an extra 3.8mm of bulk to the build plate. BUT never fear, i drafted up a quick spacer file to print as i wasn't seeing one already made. search "TMYPN Photon mono 2 spacer" on thingiverse and print that off. i used a FDM printer to do so. atm im giving this 4 stars because i feel they should really make the "print off a spacer for this these flex plates" more apparent, will edit my review post print as im skeptical about the polished metal plate.
Eighty6SVO
Comentado en los Estados Unidos el 17 de septiembre de 2024
The biggest thing with this is that it does in fact fit the Anycubic Photon S. Even though it's an older resin printer (at this point), it's nice to be able to get a removable build plate for it. In the case of this, it comes with two build plates and one adhesive magnet. So far it hasn't been an issue, but the strength of the magnet is a concern. I haven't had issues with it like I said as it is very strong. The other concern is the adhesive to the original build plate. In a brand new printer this is probably not at all a concern, but mine has been used. I cleaned the surface multiple times to give it as good of a chance as possible. So far it's been fine. That does lead to me to the big issue with this kit which is there are no instructions. It's really straightforward, but still something at all would be nice for some affirmation I cleaned the plate correctly.The two build plates are a nice touch if you need to print multiple things and don't want to wait to clean off the other plate. I'm not sure exactly what the plates are made out of, but so far I haven't seen any corrosion. The bed adhesion is pretty good too. The only failure (so far) has been the very first print. I cleaned the plates as well as I could, but it still failed about half way. Since then I've had no issues.overall, good product so far, but no instructions, information about any of the parts, care instructions, nothing is kind of unacceptable really.It should be obvious, but RESET YOUR Z-AXIS ZERO. IT WILL HAVE CHANGED. DON'T FORGET AND CRACK YOUR SCREEN.
Productos recomendados