No hay artículos en el carro
No hay artículos en el carroDescripción del producto
F80 es una resina suave y elástica. Está disponible en negro y rosa, y las impresiones pueden permanecer suaves incluso en el frío invierno.
Dado que la resina suave es difícil de imprimir, y la viscosidad de esta resina es muy alta, no se recomienda que los principiantes la utilicen.
Limpieza y post-curado
- Herramientas de limpieza: cepillo para polvo suave o limpiador ultrasónico o máquina de curado 2 en 1
- Tiempo de limpieza: 3 minutos
- Disolvente de limpieza: 95% etanol o IPA
- Fuente de luz post-curado: 385-405 nm UV (40 W)
- Tiempo de post-curado: 4-6 minutos
La diferencia entre F80 y F69
Resistencia: F80 > F69;
Dureza Shore y resistencia al desgarro, alargamiento a la rotura: F80
Las impresiones F80 pueden permanecer suaves a bajas temperaturas, las impresiones F69 se volverán duras.
Introducción al rendimiento
Propiedades mecánicas
Dureza Shore 50-60 A
Resistencia a la tracción: 3,8 MPa
Resistencia al desgarro: 9,75 KN/m
Alargamiento en rotura: 159 %
Viscosidad (25℃): 2300 mpa
Módulo elástico: 1,8 MPa
Configuración de impresión
Altura de la capa (mm): 0,05 mm
Tiempo de exposición inferior: 35-50s
Tiempo de exposición normal: 1.7-10.2s
Si necesitas configuraciones específicas, visita el sitio web oficial de RESIONE
schylar burgess
Comentado en los Estados Unidos el 16 de agosto de 2024
No se pudo cargar el contenido.
Sergio Andres Betancur C.
Comentado en los Estados Unidos el 27 de julio de 2024
Great results
Cammeron
Comentado en los Estados Unidos el 14 de abril de 2023
This resin produces awesome prints. I used an Anycubic Photon M3 Plus with the configuration file from Resiones website. The very first print came out just as good as my dialed in prints using non flexible Elegoo Water washable resins. I did not expect that.The good:The resin is very flexible, retains/returns to it's shape after being flexed, doesn't peel or break apart and picks up even fine details.The bad:It's expensive, more than you realize. Because the prints are rubber a large number of people will likely use this for functional parts which are less likely to be hollow meaning you use more of it on top of it being pricey. Aside from price it smells, and not to a small extent. At first I thought it was just a bit stronger than normal resin however I left home to go to work and came back and it hit me hard, it smells like resin mixed with tire fire. I continued to print with it with my windows open and after about 6 hours of printing noticed my eyes became irritated if I was near the printer for long periods of time (such as while cleaning batches of parts while others printed.) It's also messy. 99% IPA doesn't cut through it much. I found I hand to dunk it in IPA, rub it clean with my hands, then lightly use a toothbrush to clean the "goop" out of nooks and crannies on the parts. After that I can finally cure it.It's a great resin but it requires far more effort, twice the money, and goes half as far. I would not use it unless it was absolutely needed. It's neat, but hardly worth the cost for the novelty.
Robert
Comentado en los Estados Unidos el 22 de marzo de 2022
This resin is tricky and temperamental and takes some testing to get a good outcome. But now that I understand its properties and the environment it requires I’ve had a very successful experience and now I’m making usable parts. Maintaining proper viscosity is the key to a successful print. I made an internal heater for my printer to regulate the chamber temperature as well as measuring viscosity and resin temperature before I begin the print. If I do this I’ve had 100% success.I’m using a elegoo Mars pro 2
Client d'
Comentado en los Estados Unidos el 23 de enero de 2022
Great resin but I was unable to make a successful print on photon mono x after 20 attempts with suggested settings and any other settings. Parts keep sticking to the vat.The only part I was able to print was the calibration model which was only 3 mm highAnd it printed with nice detail. Taller parts just keep stretching the entire piece and it detached from platform or destroys the supports
Productos recomendados
Mex $667.00
Mex $ 333 .00 Mex $333.00
Mex $377.15
Mex $ 188 .00 Mex $188.00
Mex $1,321.00
Mex $ 594 .00 Mex $594.00