No hay artículos en el carro
No hay artículos en el carroDescripción del producto
PASOS DE INSTALACIÓN
1. Retira el panel interior de la puerta lateral del conductor
2. Retira el reposabrazos y el bisel del interruptor de ventana del panel de la puerta
3. Si aún está conectado, separe el soporte del reposabrazos del bisel del interruptor de ventana.
4. Retira el soporte antiguo del reposabrazos, apuntando hacia la posición donde solo hay un pequeño labio en el extremo plano del semicírculo, y las partes restantes están al ras con las partes aún pegadas en el reposabrazos. Si todo el soporte está separado, corta una junta como componente (aproximadamente 2 mm de grosor) para llenar el espacio entre el nuevo soporte y el reposabrazos.
5. Instala en seco el nuevo soporte en el pasamanos para garantizar una colocación y posicionamiento adecuados. La parte posterior del nuevo soporte tiene un semicírculo que debe estar al ras con el resto del soporte dañado.
6. Aplica súper pegamento en el lado interior del soporte restante en el reposabrazos y luego coloca el nuevo soporte en su lugar. Aprieta rápidamente el nuevo soporte con los tornillos extraídos.
7. Vuelva a montar las puertas en orden inverso.
Matt A
Comentado en los Estados Unidos el 13 de enero de 2025
The rest of my armrest was not broken, so spending the money on a complete replacement didn't make sense. The old one is bonded into the armrest, so removing it was a bit of a project. Also the new one is designed assuming that the piece around the one bolt would break off in the armrest, and the new one could just go over it. Mine did not break off, and the instructions say to use a washer or spacer in place, I opted to cut that section out of my old one for the best coverage.I used some Plastic welder epoxy, and got it all bonded in there. Works great!
RonK
Comentado en los Estados Unidos el 1 de enero de 2025
Great option to the $90 replacement armrest and was extremely easy to install. Looks like it is going to be just as sturdy as the original.
Miguel Ferran
Comentado en los Estados Unidos el 29 de abril de 2025
This item fit perfectly, saved time and money. I almost replaced the door panel.
Sam L. Jackson
Comentado en los Estados Unidos el 7 de mayo de 2024
Do you have a Dremel or other rotary tool and several cutoff wheels? Do you like making a huge mess and the smell of burnt nylon? Do you have a very large bottle of CA glue? Do you have lots of time on your hands and a broken armrest? Are you too broke to afford a $90 part?If you answered "yes" to all of the above, then this product is for you. If you answered "no" to any, then definitely don't bother. This part requires extensive fitment and relies heavily on CA glue to remain in place and actually function as a door handle. I spent way too much time getting this part into place and fitting it, and while it is holding, I would be very surprised if it held long term.See the problem with these arm rests is they get brittle over the years with heat and time, so as the armrest gets pulled on to close the door over and over, the "claws" that hang onto the door frame slowly bend out, chip, and eventually break off. The armrest this fits has 3 such claws, but this only replaces one of them. If your door is like my door, then all 3 of the claws are broken. The original part is also made of injection molded nylon like this part is, but can it do the job of three other claws when it's attached to the armrest with only a single screw and a ton of CA glue? I guess only time will tell.If I could buy this part for $5 then I would give this a better rating, but it's quite expensive for something that takes this much effort to install and probably won't work. If you value your time and don't fixing something twice, I would recommend getting a complete replacement armrest (also available on Amazon) for about $90 instead that will fix all 3 attachment points and be solid instead of glued together.If this fix holds up for more than a year, I will come back here and update this review to reflect that.
Jerod Ingels
Comentado en los Estados Unidos el 14 de diciembre de 2024
Man, I was super bummed every time I went to close my driver's door prior to this product. Things would flop around, the handle was flexin, the switch holder fell out twice, until I purchased this repair kit.I had to dig out some pieces of the old GM craptastic plastic material, (most likely produced here in my home town of Dayton Ohio) but once I did. Oh boy. Did this thing work and work well. Everything fit well, and absolutely resolved my issue! Time will tell on durability, but from initial inspection, it appears to be a good material.Thanks seller! You've enhanced my life!
Productos recomendados
Mex $360.00
Mex $ 180 .00 Mex $180.00
Mex $1,858.48
Mex $ 892 .00 Mex $892.00