No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Rendimiento maximizado
Las cuchillas han sido diseñadas para maximizar el rendimiento en aluminio y otros metales no ferrosos. Producen muy pocas chispas y poco calor, lo que permite que el material de corte sea manejado rápidamente.
Funciona en muchos metales
El carburo especialmente formulado dura más tiempo y deja cortes limpios y sin rebabas en todo tipo de metales no ferrosos como aluminio, cobre, latón, bronce e incluso algunos plásticos.
Reducción de ruido y vibración
Nuestras cuchillas de metal no ferroso han sido diseñadas con puntas de carburo de tungsteno de grano micro de precisión y una configuración de dientes de triple chip. Los 25,4 cm y más grandes también cuentan con ranuras de expansión enchufadas de cobre para reducir el ruido y la vibración, mientras que cuenta con rejillas de ventilación de calor para un funcionamiento más fresco.
John
Comentado en los Estados Unidos el 1 de agosto de 2024
The blade cut great clean cuts on the first 3 pieces of metal then it raised the white flag on the fourth cut. There are better blades out there. This one was pricey so I was disappointed.
Restoration Hobbyist
Comentado en los Estados Unidos el 14 de marzo de 2024
For starters, let me say that I'm impressed that any circular saw blade can cut steel in a controlled manner. I worked this blade reasonably hard, cutting 1/4" (6mm) mild steel box tubing. It made two 12" rip cuts without problems. When I then tried to cross cut the same steel, it made it all but 1" through the crosscut. The blade teeth still felt sharp, but all it would do was roll the steel and then stopped cutting. All told, I cut 31" through 1/4" steel at a cost of $41.32 for the blade ($1.33/ inch). I also found the 5/8" adapter to be worthless, since it was a bit too small to fill the 1" arbor hole. It cost me another $10.60 for a kit of decent adapter rings, adding another $.33/ inch to the project. I still have nine more crosscuts to do. Not sure if it's worth it to buy another blade or two. If it had made it through my project I'd give the product five stars. It cut in a controlled manner and didn't generate excessive heat. But I'm struggling to give it three stars -guess I'll give it the benefit of the doubt.
Jonathan Allan
Comentado en los Estados Unidos el 11 de noviembre de 2024
The 5/8 in bushing isn’t usable with my saw, a Metabo HPT, it slipped out while I was operating the saw. I’m out of the return window because I thought there was no rush as there would be no way this could be a problem. If you have a 1” arbor it probably works just fine!
Stoned up North
Comentado en los Estados Unidos el 11 de septiembre de 2022
Cut through the sheet metal like butter, I did do a rookie mistake by not using a zero clearance insert but it was not a precision cut. This blade will work with a 5/8" arbor when using the included insert but it did take few tries to get it on correctly. it's well worth the money.
israel Escamilla
Comentado en México el 15 de julio de 2021
buena calidad similar a los diablotodos estos productos necesitan bajar mas de precio
LGM
Comentado en los Estados Unidos el 21 de julio de 2020
These hold up well, I get a reasonable number of cuts from them. I'm usually cutting 3"x3"x1/8" square tubing, 2"x2"x3/16" angle iron and 1"x2"x1/8" tubing. Go slow, watch for chatter and let the blade do the work. They compare favorably with the Diablo blades I've been using.
Productos recomendados
Mex $1,208.02
Mex $ 495 .00 Mex $495.00
Mex $795.00
Mex $ 381 .00 Mex $381.00
Mex $3,499.99
Mex $ 1,749 .00 Mex $1,749.00
Mex $586.00
Mex $ 269 .00 Mex $269.00