No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Nota de importancia：
✔ Para Ender 3, sólo tiene que conectar y empezar a imprimir.
✔ Para Ender 3 v2/ Ender 3 pro/ Ender 3 Max/ Ender 3 Neo/Ender 3 V2 Neo/Ender 3 Max Neo, por favor actualice el firmware. NO LO INTENTE AL AZAR.
✔Si usted tiene cualquier otro problema con la actualización del firmware, puede consultar los vídeos de flash de firmware disponibles en nuestra página de producto.
Especificaciones del producto
- Versión: V4.2.7
- Voltaje: 24V Entrada/12V Salida
- Firmware: V0.0.6/V1.0.6 basado en Marlin 2.0.1
- Controlador del motor paso a paso: TMC2225
- Los drivers TMC2225, Marlin 2.0.1 y bootloader han sido preinstalados.
Miguel Ángel Rodriguez
Comentado en México el 10 de febrero de 2025
Tal vez fue mala suerte pero en la primer prueba se quemó.
Timothy McNabb
Comentado en los Estados Unidos el 25 de enero de 2025
I had the 4.2.2 board shoot craps, so I ordered this as a replacement/upgrade along with the CR-Touch. It is an intermediate-level effort. On my unit, plugs had some hot glue on them to hold them in place. I used a syringe with a bit of rubbing alcohol to break the hot-glue bod with the plastic and it picked right off.Switch one plug and one wire at a time. Be patient, and watch a couple YouTube videos.
Michael Wilson
Comentado en los Estados Unidos el 21 de enero de 2025
I had accidentally damaged the micro USB port on the original board for my Ender 3 V2. Rather than trying to replace the port, I figured I’d get this as an upgrade. It has worked well for me so far. The noise from the motors are almost non existent, which is fantastic. The only noise from the printer are the fans. Creality’s installation tutorial was clear enough for me and there are also plenty of other guides out there too. Just be warned that it does take some time to swap out. I can confirm it works with the mriscoc firmware as well if you are inclined to use that.
Conor Hildebrandt
Comentado en Canadá el 11 de enero de 2025
If you have an Ender 3 and have to listen to it get this upgrade immediately. The difference is insane and it's so nice to have such a quiet machine. I'd never buy another Ender 3 again but if I did I would get another one of these boards
Scrimshaw
Comentado en los Estados Unidos el 23 de mayo de 2024
I got this board installed easily enough on my (1st generation) Ender 3 Pro by following some online video tutorials. The biggest challenge was the old board had all of the connectors hot-glued, so I had to peel off a lot of glue to release the connectors from the old board. However, once that was done, this was fairly straightforward to install.I was also installing a BL touch at the same time, and I wasn't sure if the firmware on the board would support it out of the box, so I downloaded the appropriate code from the Creality website. The most current code I could find on their website for this V4.2.7 board (that supported BL touch) was Marlin V2.0.6 (under the basic Ender 3 section, not the Ender 3 Pro section).The only odd thing I've noticed is that when it's auto-leveling with the BL Touch, this board intermittently turns off the hot end, so it cools while leveling, and then you get a thermal error about 10 seconds into the print because the nozzle is too cold. I have searched online for an answer to this, and haven't found the "right" answer (to keep the hot end turned on during leveling), but did find a work around by adding an M109 command to my startup Gcode, to force the hot end to heat up again. I wish Creality kept their code more current, so hopefully this helps you if you encounter this problem with this board.Overall, I love this board. It's super silent, and the only noise is the fan. Rarely you can hear a bit of stepper noise (just barely) for a moment when it's printing an interesting curve, but that's it. Even with Creality's outdated firmware, I'm giving this 5 stars.
Miguelonmex
Comentado en México el 13 de diciembre de 2024
Éso si, tuve que flashear el firmware para que quedara como a mi me gusta.Y si es silencioso a comparación de la tarjeta original de mi Ender 3 pro.
Alejandro solano lara
Comentado en México el 13 de diciembre de 2024
Esta bien 1200 es un abuso ...Pero está muy buena en general
luis fernando
Comentado en México el 18 de octubre de 2024
Excelente, funciona perfectamente y no hace ruido, aunque me lleve un pequeño susto cuando la instalé, el pequeño ventilador no giraba cuando hice la prueba, era porque tenías que ponerle manualmente las revoluciones si lo querías probar, todo lo demás bien.
OscarE
Comentado en México el 10 de septiembre de 2024
No se pudo cargar el contenido.
BrokenCinder3
Comentado en Canadá el 19 de septiembre de 2023
I just got finished installing it and have only run a couple very short prints but I’ve been doing a bunch of upgrades to my Ender 3 and this is for sure one of if not the best one I’ve done so far. It makes the motors whisper quiet and I needed a new board anyway because when I was doing some other work I accidentally fried something in the other one so that the centrifugal fans would never kick in. Oops right. Also I don’t know if it’s just upgraded firmware or something you can only get on a different board but it has a different version of the firmware on it and it has a different layout with more features which is super nice. And also I’m hoping this one won’t have some of the glitches the original board had as I haven’t had any come up yet where it would on the original. One thing to keep in mind is they don’t send very good instructions for swapping over but if you’re at this point of messing with your printer I’m sure you have a good enough understanding of it to do everything. And if you’re nervous just take pictures and mark where things go. It is just a plug and play swap. Overall great upgrade and highly recommend.
Productos recomendados
Mex $876.00
Mex $ 446 .00 Mex $446.00