Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Placa de construcción de acero con resorte PEI con textura PEI de 310 x 315 mm (con base magnética), superficie de construcción flexible para impresora 3D Creality K1 Max

Envío gratis en pedidos superiores a Mex $600.00

Mex $787.98

Mex $ 378 .00 Mex $378.00

En stock

1.:220x220mm


2.Color:Peo Suave+pei Texturizado


  • Impresora compatible: placa de construcción de 310 x 315 mm para impresora 3D Creality K1 Max.
  • El paquete incluye: hoja PEI PEY (con base adhesiva magnética), con agujeros para tornillos, el tamaño de la placa de construcción es de 310 x 315 mm.
  • Resistente a altas temperaturas: la cama PEI puede ser resistente hasta 260 °C para la boquilla sin deformación. La superficie PEY puede funcionar a una temperatura alta de 120 °C. Después de nuestras extensas pruebas, recomendamos que PEY imprima PLA / TPU / PETG. (sugerencia de temperatura: 50 ℃-70 ℃, ≤90 ℃); PEI para imprimir PLA /PLA-CF/PETG/PC/ABS /TPU, nailon, etc.
  • Excelente calcomanía para la primera capa de impresión: la placa flexible de acero de resorte PEI y PEY tiene un buen calcomanía. Incluso se puede pegar bien sin calentar la plataforma, no necesita pegamento.
  • Flexible y fácil de quitar: la hoja de acero de resorte PEI+PEY es flexible. Las impresiones se pueden quitar fácilmente a mano una vez que la superficie de construcción se haya enfriado, o doblar la placa de construcción y quitar las impresiones. La alfombrilla de impresión no estará fuera de forma.


RETUXEP PEY liso + placa de construcción de acero con resorte PEI texturizado de 310 x 315 mm (con base magnética) superficie de construcción de cama de impresión flexible para impresora 3D Creality K1 Max


Corey
Comentado en los Estados Unidos el 20 de mayo de 2024
I picked up one of these to use with my 300mm Voron Trident. Having the extra 10mm doesn't affect anything at all, and is actually easier to slap down than the factory 305mm plate it came with.The textured PEI side is super fine and leaves an awesome finish. The PEO side also leaves a nice fractal look on my prints. I have a total of three build plates for the Trident, and this one has the nicest PEI out of them all.
Christy L. Smith
Comentado en los Estados Unidos el 17 de febrero de 2024
To the two people that had adhesion issues with this bed, my first print was flawless, then the second one didn't properly stick, the third was worse. And it just kept getting worse too. I was cleaning the bed between prints with 99% isopropyl alcohol and paper towels like I always did, but it was just getting worse. Out of desperation, remembering reading that PETG (I wasn't using PETG, but hey, I was desperate) works best on a build plate after washing with soap and water, I tried that.I then returned my Z offset to the original setting and printed a test print. FLAWLESS print quality on the PEO side. The texture is beautiful, and my latest print (a fireplace phone holder) looks stunning. I'm not even sure I want to paint it now it looks so good.FOR Z OFFSET, this is something I had been putting off, or doing wrong, FOR YEARS. The best way to do this is live z offset, but when I tried what others suggested, I honestly couldn't tell what I was looking at, and couldn't get a good bed. Paper trick is good, but is ONLY the start. The biggest thing to remember with that is that paper still has a thickness and you're telling the Z Offset that there IS NO thickness between the nozzle and the bed. You still have to dial it in further.Now, in whatever slicer you use, add a primitive block, resize it to fill the bed, and be only .2mm thick (you only need one layer for this). Change your Z Offset from what you dialed in with paper, to .1mm lower than that. Then, in your live z offset - change it to .15mm lower again to start this process, and start the print. After roughly 5% of the print is done (it will create a diagonal bar at .15mm "too low"), raise it while it's still printing .05mm. After another 5%, raise it another .05mm. Do this until you have either printed it at .15mm too low, to .15mm too high, or until the print stops sticking to the bed (no need to try beyond that.Remove the print from the bed. This should peel off like tape on a smooth surface, don't pull TOO fast, but it should come off relatively easily. Now look at the bottom of the print. The smoothest bar is the right Z Offset. If it's too low, it will be smooth in sections, but other areas will peel up from the bed as a result of the nozzle scraping the plastic. If it's too high, the lines won't be pushed down far enough to stick together properly so will have very fine gaps in the surface.Count the number of bars from the very first in the corner - if the best print is the first bar, your Z Offset should be -.15mm lower than what you set at the start of this all. If it's the second, it should be -.1mm. If it's the third -.05mm and so on. Using this, you WILL get perfect bed adhesion and beautiful prints, even on an Ender 3.
Jp
Comentado en Canadá el 5 de octubre de 2024
fits nicely on my ender 3 pro as well as my k1se :0 would buy again
NK
Comentado en Canadá el 21 de octubre de 2023
The black pattern is sweet! Good adhesion on both sides and fits perfectly on my E3V3SE.
C. Yang
Comentado en los Estados Unidos el 13 de octubre de 2023
This sheet came with one side textured PEI, and the other side has a triangle pattern PEO. The textured PEI side is similar to most other gold textured PEI sheets you can find on the market from Comgrow, Creality etc. and it works just as well as the others. That is to say, PLA and PETG sticks to the surface with no additional adhesives, etc. and just pops off when the print is cooled down.The real reason you get this one is because the flip side has a patterned PEO, and I am enjoying the pattern that it leaves on the bottom of the parts. Similar to the textured PEI side, you don't need any adhesives on the plate to get PLA to stick, I've printed about 10 parts on it so far and haven't had any adhesion issues. I've attached a picture of the underside of a jar that my wife printed.The sheet itself is dimensionally accurate to a Ender 3 bed, the edges are sharp and there are no peeling layers that you sometimes get with poorly manufactured sheets. This is a great buy!
Productos recomendados

Mex $388.16

Mex $ 186 .00 Mex $186.00

4.7
Elegir