No hay artículos en el carro
No hay artículos en el carroSealPro - Fuelle de puerta para lavadora
Shopper5
Comentado en los Estados Unidos el 17 de agosto de 2023
The W10290499, W10381562 Washer Door Seal from SealPro was exactly as advertised. I assume that it is a third-party manufacturer (i.e., not an OEM Whirlpool part), but it sure looks and feels perfect, and is working just fine, and for much less money. Doing the swap out on my Whirlpool clothes washer WFW9151YW00 was not difficult, but does require a few tools, one of which is a star screwdriver (i.e., Torx tip) to detach the left side of the control panel (behind the removed detergent drawer). The control panel just pops off after removing that screw, and the small Phillips screw under its "chin." I did not use a spring spreader tool to remove and install the outer boot spring (see photo), but instead spread the outer boot spring with two small screwdrivers, and some patience. I also found that the wires that connect to the door latch are difficult to unplug, but that this can be avoided completely if you remove the two Torx-head screws from the front of the door latch, that hold that assembly. (Do this after removing the front panel that carries the door.) Again, the seal from SealPro was perfect, and solved my leakage problem.
Jackfe
Comentado en Canadá el 27 de marzo de 2023
It fits and decent quality, having my first wash and making sure its working fine, install was a bit hard but nothing crazy, took maybe 2 hours, to put the last spring was a pain had to get my wife to help.
Triggs
Comentado en Canadá el 9 de enero de 2021
We needed this quick as our washing machine sprung a leak and local appliance parts store said 5 weeks to order it in - Amazon provided it next day (we had to sign up for trial Amazon Prime to get free next day delivery). I soaked it in warm water out of the box for half an hour and then dried it off and then began to install as per YouTube video and of course knowing how the old one came off (lasted just over 7 years until sprung a leak) - I recommend removing old one day before and taking your time, familiarizing yourself with inner parts and ensuring everything is cleaned - don’t forget to clean glass on inside of door where calcium can build up and inhibit proper seal. Installing outer wire clamp was difficult as was too tight and required stretching by my wife and I pulling on the attached spring - I then had her hold it in place while I pulled last bit into slot...without her help I don’t think I would have got the wire clamp back on by myself. Initial inner wire clamp had a screw that attached the two ends of wire together so u can remove that and makes for easy install on new one.This overall was an easy fix and price was right at $180 Canadian as opposed to buying a new washer at Costco for $800 plus tax - not to mention installation hassle etc..I’m VERY happy thus far, 3 leak-less loads in - 5 stars for Amazon ***** Thank you sooooo much!Pictures are of old one as I took machine apart to remove it.
OldCornbinder
Comentado en Canadá el 17 de abril de 2019
Okay, if you’re here then you too are another front-load sucker. This job needn’t be awful. Do yourself a favour and follow the instructions in every single YouTube video out there; getting this slut on without taking everything apart is challenging. Getting the old one out with two screwdrivers and 10 seconds by no means betrays how the instal will be. This piece fits, works, doesn’t leak and will do what you need for a good price and with lighting-fast shipping. 5 star! Ease of installation? Just take the housing apart and you’re golden. I tried and tried and tried and eventually just removed the stacking lid, pulled the whole goddam place apart, said some awful things my toddler repeated in front of my wife and found 35 cents in change. If you succumb to taking the machine apart, the instal will go well. Now that I’ve done it once, I think I could do it without disassembling the whole goddam housing. I’ll never know though because this front-load nonsense ends when this machine does. Good part. Does what it says. Fits. Hallelujah! Only one screw left over. Could have fallen out of a pair of pants during a wash cycle. No problem.
tmj
Comentado en los Estados Unidos el 17 de mayo de 2018
I want to start this review stating that this fits the Maytag 2000 front load washer Mod-MHWE200XW00. I had to read many reviews to find out if this would work for my machine and it took awhile to find one that said it did. To save you even more time, Amazon also has the best price by far on this bellow especially if you have prime for free shipping with a two day delivery! I replaced this part because of the washer leaking and tearing/ruining clothes. There is a bit of work to take the washer apart to replace the bellow but since this is the third time I have had to replace this part I have it down to a science. Besides putting the ring with the spring on :/ that part takes two men and a boy to get done. There is a reason you need it and I will post a photo at the end of this review so you can see for yourself. There are several ‘how to’ videos on YouTube if you need a little extra help. I will state as some of the other reviews say it does fit a little sloppy, a little water does pool sometimes and it does have a little bit of an unpleasant smell. With that being said I will also tell you, it fits, it’s a great price, it’s not to hard to do yourself, it saves paying the repair man, I had it in two days without expensive shipping and laundry stacking to the ceiling waiting for it to get here, it doesn’t leak anymore, the funny smell is going away with use and the price was right! After much research I have found that replacing the bellow to this washer because it leaks or develops a hole in it over time is a very common problem. Wish I had researched that more before I had purchased the washer! Live and Learn...Good Luck :)
Productos recomendados