Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Sierra de metal de acero de 30 mm con 2 brocas, cortador de agujeros para metal grueso, acero inoxidable, hierro y madera (30 mm)

Envío gratis en pedidos superiores a Mex $600.00

Mex $199.12

Mex $ 113 .00 Mex $113.00

En stock

1.Tamaño:32mm ( 1-1/4 Inch )


Acerca de este artículo

  • Diámetro de corte: 30 mm
  • Amplia aplicación: acero inoxidable, aleación de aluminio, hierro, metal, madera
  • Material: acero de carburo, aleación de acero
  • Aplicación: la sierra perforadora es adecuada para taladro eléctrico de mano, máquina de perforación CNC, etc.


Diámetro de corte: 30 mm


DRM
Comentado en los Estados Unidos el 25 de marzo de 2025
cuts like a knife through butter.
Rich
Comentado en los Estados Unidos el 21 de abril de 2025
Worked great. Made fast cots through metal
Usuario de México
Comentado en México el 3 de agosto de 2024
Lo quería utilizar para instalar medidores de corriente en un centro de carga. La broca central tiene una punta muy gruesa y costó mucho trabajo mantenerla en su lugar. Los dientes de la copa son muy gruesos y se atoraron a cada rato en la lámina. Acabé usando una broca escalonada.
Juanfco
Comentado en México el 8 de junio de 2024
Si fue de mi agrado, de buena calidad
Rodolfo
Comentado en México el 18 de marzo de 2024
Lo he utilizado 2 veces y funcionó muy bien.
CB3
Comentado en los Estados Unidos el 21 de febrero de 2024
I received this 63/64” (25mm) hole saw and immediately put it to work to drill a hole for the ignition switch for my current project — 1” was slightly too large. It cut a very clean and accurate hole in the steel dashboard.Looks to be very well made; much better than stamped steel stuff at local hardware stores. I may use it again, but have let friends know it’s available for their project.Good tool at a reasonable price!
Christopher Dembrow
Comentado en los Estados Unidos el 25 de diciembre de 2024
I used a 1.5" bit for cutting 4 holes in 2" by 0.25 tube steel to insert dom pipe for a project I'm doing. Fitment was pretty spot on, but understand that I am no machinist and tight tolerances are not required for what I'm building. My drill press can do 250 rpm minimum and I did experience chatter and binding. This is likely due to the limitations of my press. It quieted down once the cutters got about to 75% of their height into material. I used lots of engine oil and took my time. If I could dial it down to 80 to 200rpm it would have probably worked better. Despite that, it completed the task that it needed to without failure of any kind. It was well worth it for my needs.
Jake Mateo
Comentado en los Estados Unidos el 14 de octubre de 2023
I bought this bit for a job and it couldn't even make a single hole. Not even halfway through a piece of very thin 16ga mild steel the bit threw two of the teeth off the bit and completely deformed. Absolutely useless. Find another bit if you want to actually use it.
Productos recomendados

Mex $435.00

Mex $ 213 .00 Mex $213.00

4.9
Elegir

Mex $388.28

Mex $ 194 .00 Mex $194.00

4.9
Elegir

Mex $187.00

Mex $ 108 .00 Mex $108.00

4.9
Elegir