No hay artículos en el carro
No hay artículos en el carro
Descripción:
Nombre del producto: impresora 3D MK8 Bowden Extrusor.
Utilizado para: todos los filamentos de 1,75 mm.
Material: aleación de aluminio de metal.
Color: rojo.
Patrón: mano derecha.
Ventajas:
1. Actualización de engranajes duales, fácil para alimentar, sin bloqueo, mejor presión empuja el filamento en la boquilla de la impresora; resorte de actualización, muy fuerte, no se deforma fácilmente.
2. El driver de aleación de aluminio original se suministra con CR-10S PRO. También se puede instalar en Ender-3, Tornado... estable y duradero.
3. Aleación de aluminio totalmente metálica, bloque de aluminio de bricolaje, necesita ser montado por ti mismo.
El paquete incluye:
1 kit de extrusor de metal Mk8 para impresora 3D Creality
B. Vincent
Comentado en los Estados Unidos el 17 de julio de 2022
This extruder pulls the filament thru without crushing, or deforming it. Easy to install by watching the video on the site. You MUST REDO your esteps for this product. My Stock estep was 94, but with this one it's 135. The dual gears are smaller in diameter, so more turns are needed for same length of filament. There are many videos on youtube on how to do this. Easy install and calibration.
J
Comentado en Canadá el 9 de enero de 2022
A bit confusing to install and calibrate, but once finished it seems to have greatly improved print quality. Is also easier to change filament now than with the stock Ender 3 extruder.
P90Xman
Comentado en los Estados Unidos el 16 de julio de 2021
Could not figure out why after dozens of good prints, they all started to fail 1/2 way thru. Found out thru a youtube video that the plastic tensioner supplied with the printer is prone to fail and crack where you can't see unless you remove it. Same identical crack, same location. Researched aluminum tensioners and upgraded to the duel tensioner! Everything is back to normal. During installation of the new aluminum tensioner you should pack the bearing with grease to extend the life of the unit!
William Dotson
Comentado en los Estados Unidos el 23 de octubre de 2019
So I want to try and be fair to this product as the build quality is very good, however I thought since this was made for the CR10 I could just bolt it in and get printing and that would be that. The fact that this item comes without directions is unacceptable, make a YouTube video or a PDF if you don't want to include printed directions but it needs instructions. The one thing I wanted to make clear is this requires modified E steps in order to work properly. I was under-extruding by 30% after installing this. Because the CR10 cannot load new firmware this became an issue, one that I solved by adjusting E-steps in my slicer but some might not be comfortable with that. Other than that the extruder works very well, which is why I gave it 4 stars, but it is not as simple as bolting it on and away you go.
Michael
Comentado en los Estados Unidos el 22 de septiembre de 2019
Well so far it is working very well. It pulls really good with no slipping so far. There is no instructions which always makes me mad. I can assemble about anything but I know some people cannot. One warning on the gear assembly that is ready to go do not over tighten the bolt or you will lock the gear up. The gear that goes on the stepper shaft should have two set screws instead of one. You will have to make sure the gear on the stepper motor aligns at the same height as the other one or it may not pull right. This is worth the money because if you get a roll of pla that has the diameter too small this will make up for it.
Productos recomendados
Mex $600.00
Mex $ 312 .00 Mex $312.00
Mex $388.54
Mex $ 202 .00 Mex $202.00
Mex $4,117.95
Mex $ 1,881 .00 Mex $1,881.00
Mex $329.00
Mex $ 177 .00 Mex $177.00
Mex $344.00
Mex $ 154 .00 Mex $154.00